759842
19
Zoom out
Zoom in
Previous page
1/38
Next page
© Outdoor Life Group Nederland B.V. - v16.1 -17-
www.outdoorlifeproducts.com
Leggen EPDM-dakbedekking
D GBNL
EPDM aandachtspunten
Spraybond contactlijm niet verwerken beneden 5
graden Celsius.
• Ondergrond dient schoon, droog en vetvrij te zijn.
Uw dakvlak dient 100% waterpas te staan of
aopend richting hemelwaterafvoer.
Plooien en permanent water in/op uw EPDM
dakbedekking heeft geen nadelige invloed op de
duurzaamheid.
Volledig gekleefd
1 EPDM folie voor de helft terugvouwen
2 Lijm aanbrengen op onderconstructie
3 Lijm enkelzijdig aanbrengen, verbruik: 6M2/L
4 In de handdroge lijm de EPDM ‘spanningloos’
aanbrengen (opstaande randen pas lijmen nadat
het dakvlak is aangebracht)
5 EPDM aandrukken d.m.v. zachte borstel
Overlap bij extra overkapping:
Overlap EDPM folie dient minimaal 8 cm te zijn
Kitten idem als hemelwaterafvoer
Er dienen minimaal 2 rillen kit naast elkaar tussen de
overlap aanwezig te zijn
Controle: De kit moet aan de rand goed zichtbaar
zijn, dan is de overlap goed geplakt!!
EPDM-Folie Verlegehinweise
Den Spraybond Kontaktkleber bitte nicht unter 5
Grad Celsius verarbeiten.
Der Untergrund muss sauber, trocken und fettfrei
sein
Das Dach soll 100% waagerecht sein oder zum
Fallrohr schräg abfallen.
Falten und ständig stehendes Wasser auf Ihrer
EPDM Dacheindeckung haben keinen schlechten
Einuss auf die Dauerhaftigkeit.
Vollständig verkleben
1 Die EPDM Folie bis zur Hälfte zurückfalten.
2 Den Kleber auf die Unterkonstruktion auftragen.
3 Leim Einseitig anbringen, Verbrauch: 6M2/L
4 Wenn der Leim angetrocknet ist, können Sie die
EPDM Folie spannungsfrei auf das Dach befes-
tigen verlegen. (Die überstehenden Dachränder
werden erst verklebt, wenn die Folie verlegt ist)
5 Die EPDM Folie mit einer weichen Bürste fest
andrücken
Überlappung der Folie für die extra Überda-
chung:
Die Überlappung der EPDM-Folie soll mindestens
8 cm betragen. Das Verkleben geschieht wie bei
der Fallrohrverbindung beschrieben. Zwischen der
Folienüberlappung müssen mindestens 2 Rillen Kitt
sein. Prüfung: ist der Kitt am Rand deutlich sichtbar,
dann ist die Überlappung einwandfrei verklebt.
EPDM Points of interest
Do not use the Spraybond close contact glue with
temperatures below 5 degrees Celsius
The foundation needs to be clean, dry and grease-
proof.
Your roof needs to be 100% level or sloping to the
drain pipe.
Fully glued
1 Fold back the EPDM rubber to the half.
2 Put the glue on the roof.
3 Apply glue unilateral, consumption: 6M2/L
4 When the glue is hand-dry, you can put the EPDM
on the roof without tension
(you can glue the raised edge after you afxed the
EPDM on the roof itself)
5 Push the EPDM with a soft brush.
Overlap with extra roof extension:
The overlap has to be at least 8 centimeters.
Glue it the same as the drain pipe.
There have to be at least 2 grooves of glue between
the overlap.
Check: when the glue is visible at the edge, the
overlap has been glued well!
1 2 3 4
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Outdoor Life Beuk at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Outdoor Life Beuk in the language / languages: All languages as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info