589268
6
Zoom out
Zoom in
Previous page
1/10
Next page
6
GB
If more than one remote sensor is being used, the unit can auto-
matically scan all three of the outdoor channels.
To use the automatic outdoor channel scanner function:
Press and hold [CHANNEL] for about 2 seconds. The unit will
begin a cycle of continuously rotating through the three channels.
Temperature readings from each site will be displayed for approxi-
mately 5 seconds.
To stop the automatic scanning function, press [CHANNEL] again.
The scanning cycles will stop.
The kinetic wave display on the channel icon indicates the status
of reception.
If no readings are received from one particular channel for more
than two minutes, blanks will be displayed until further readings
are successfully searched. Check the remote unit is sound and
secure. You can wait for a little while or press [CHANNEL] and
[MEMORY] simultaneously to enforce an immediate search. Of
course no reading will be shown if no remote unit is assigned to
that channel.
The JTR-168LR is capable of measuring temperatures within the
-50°C (-58°F) and +70°C (+158°F) range. If the temperature goes
above or below that, the display will show "HHH" or "LLL".
MAXIMUM AND MINIMUM
TEMPERATURES
The maximum and minimum recorded indoor temperatures and
those of each channel will be automatically stored in memory. To
display them,
1. Press [CHANNEL] to locate the desired channel.
2. Press [MEMORY] to rotate through the maximum [MAX],
minimum [MIN] and current temperatures. The readings of the
indoor temperatures will also be displayed.
To clear the memory of a particular channel
1. Press [CHANNEL] to locate the desired channel.
2. Press [CLEAR], the MAX and MIN memory for that channel
will be erased. Note it will also erase the memory for the indoor
temperatures. If you press [MEMORY] now, the maximum and
minimum temperatures will have the same values as the current
ones until different readings are recorded.
DISCONNECTED SIGNALS
If without obvious reasons the display for a particular channel goes
blank, press [CHANNEL] and [MEMORY] to enforce an imme-
diate search. If that fails, check if the remote unit of that channel is
still in place. Make sure the transmission is within range and path
is clear of obstacles and interference.
The unit is in searching mode.
Temperature readings are
securely registered.
No signals.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oregon Scientific JTR168LR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oregon Scientific JTR168LR in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oregon Scientific JTR168LR

Oregon Scientific JTR168LR User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info