492719
17
Zoom out
Zoom in
Previous page
1/30
Next page
© Calibre UK Limited Issue 1.30 27 January 2012, W: www.calibreuk.com
T:+44 1274 394125 F: +44 1274 730960 E: techsupport@calibreuk..com 13
3.5.6. I/O Lock
Settings: On, Off
If I/O Lock is switched off the output is run with a fixed refresh rate determined by the frame rate setting,
which deviates from the input refresh rate, even if both are nominally at the same rate. This causes
occasional frame dropping or repeat. If I/O Lock is on the output refresh rate is following the input
refresh rate. This is achieved by modulating the output clock and works if input and output refresh rate
are nominally at the same rate, e.g. when frame rate is set to 60Hz and the video input is also 60Hz. If
e.g. the video input rate is 50 Hz and the Frame rate is set to 60Hz, the output is in free run mode. The
status line of the OSD window under Sync Mode indicates if the output signal is locked to the input
signal (I/O Locked) or in free run mode (Free Run) .
3.5.7. Native Color Temp
Settings: 5500, 6500, 7500, 9300, 10000
Native Color Temp allows the user to select from pre-configured color temperatures to match the
display. If both Native Color Temp set here in the Output menu and Color Temp set in the Color menu
are set to the same value, no conversion is performed.
3.5.8. Output Gamma
Settings: 1.0 to 3.0 in steps of 0.1
Output gamma allows to re-gamma video signals with pre-configured gamma values to match the
display. Input gamma and output gamma both default to 2.2. If they are both set to the same value,
there is no effect on the image.
Note: If e.g. an adjustment to reduce the level of red in the image is required, select a higher number for
the (input) Color Temp in the Color menu, or a lower number for the Native Color Temp in the Output
menu.
3.6. Color
This menu contains adjustments associated with setting up inputs to the unit. Use the Up and Down
keys to scroll to the required item and press the Menu key.
3.6.1. Black-Level Offset
Settings: 0 IRE, 7.5 IRE
Used to select 7.5 IRE black level set-up adjustment. Should always be set to 7.5 IRE for HDMI video
inputs and should usually be off for analog video inputs.
3.6.2. Black-Level
Settings: -50 to 50 in steps of 1
Black level controls the offset applied to the video signal.
3.6.3. Contrast
Settings: -50 to 50 in steps of 1
Contrast controls the gain applied to the video signal.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Optoma HQView-300 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Optoma HQView-300 Series in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info