492719
15
Zoom out
Zoom in
Previous page
1/30
Next page
© Calibre UK Limited Issue 1.30 27 January 2012, W: www.calibreuk.com
T:+44 1274 394125 F: +44 1274 730960 E: techsupport@calibreuk..com 11
A factory reset can also be applied when pressing the factory reset key combination at power up. The
keys have to be kept pressed for about 10 seconds until the RGB(S) input LEDs stop flashing. If the
keys are released during that 10 seconds period the system will get into Updater mode (see chapter 5)
since the Menu key is part of this key combination.
2 YPbPr / RGB(S) video input
3 DVI-I connector featuring a DVI-D input and a VGA input
4 DVI-I output connector (only the digital DVI-D is supported, HDMI 1.3 receivers can be connected
with a DVI/HDMI adapter cable)
5 TCP/IP port
6 USB port
7 RS232 port
8 Power supply connector
3.3.
Main Menu
The main menu lists the input channel select item, 6 sub menus, and a menu item for automatic setup
of VGA modes. The 6 sub menus are Output, Color, Geometry, Enhancement, System and Multiple Unit
(only HQView-310 and HQView-320).
On each menu page an Exit menu item is available to leave the menu or submenu. Some adjustments
are not applicable to all signal types or operating modes, in which case those non-applicable functions
will be ghosted and are not accessible via the menus.
All menus have a top status line and a bottom line indicating the firmware revision number. In the status
line the currently selected input channel is indicated and the detected mode is identified. The firmware
revision number displays the revision number of the bootloader behind BL, the revision number of the
firmware behind FW and whether it is a 300S, 310, 320 type HQView unit.
To set up your HQView-3xx it is recommended that you follow this procedure:
Choose the correct output mode and parameters to suit your screen or projector.
Select the correct input signal.
Set the input levels and features appropriately to optimize the appearance of your image.
Set any other parameters to suit your application.
Note: All Input parameters are specific to your chosen input channel and input signal type, they are not
global to the unit. All Output parameters are global
3.4.
Input
The list of available inputs can be scrolled through using the Up and Down keys. The new input is not
selected until the Menu key is pressed.
The list of inputs are: Component, VGA, DVI and Test Pattern.
Test patterns can be generated by HQView-3xx without needing an input connected. When Test Pattern
is selected as the input, the required test pattern can be chosen with the menu navigation up/down keys
when the OSD menu is off.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Optoma HQView-300 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Optoma HQView-300 Series in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info