424646

Opentel ods 3000 ci set Manual

10
Zoom out
Zoom in
Previous page
1/15
Next page
Free To Air / Common Interface Digital Satellite Receiver
MENU OPERATION
17
Free To Air / Common Interface Digital Satellite Receiver
MENU OPERATION
16
3. INSTALLATION
Installationmenu helps you to setup a variety of
parameters necessary for receiving signal, add new
service, upgrade the new software and reset the
channel data.
Select Installationmenu in main menu, and you will
be asked to enter your PIN code.
You can find the following Installationscreen by
entering it.
3. A. AUTOMATIC CHANNEL SEARCH
Your receiver includes the preprogrammed information of transponders contained in various
satellites.
You can update the transponder list preprogrammed
for a satellite by adding a new transponder to it or
modifying the information of the existing transponder.
(Refer to the Manual Channel Search described in
section 3.B) Select Automatic Channel Searchmenu
in Installationmenu and the following screen will be
displayed.
Select the desired satellite using the left / right
keys(
).Set LNB Power, LNB Type, LNB
Freq, 22KHz
”,Search Option, and DiSEqC
Typefields to the appropriate value using the left / right
keys(
) at each field.
LNB Power
LNB Type
LNB Freq.
TP Freq.
22KHz
Search option
DiSEqC Type
Motor
: Depending on the users antenna LNB, you can supply either LNB power by
setting ONor not by setting OFF. Normally set this to ON.
: You can select the LNB type.
: You can select the predefined LNB frequency or manually enter a specific
frequency in MHz unit by pressing numeric keys.
: You can select the TP Freq.
: In case you are using two antennas connected to a 22KHz tone switch box,
you can supply either 22KHz by setting ONor off by setting OFFto
select antenna.
: You can search all the free channels & scramble channels or only free
channels or only scramble channels by setting the search option.
: If you have DiSEqC box, you can choose port by selecting port number.
Otherwise, choose none
: If you have a DiSEqC 1.2 motorised system, then you can take
advantage of the DiSEqC 1.2 functions available.
you can select the “User”or”Installer” and then press “F1” key.
After that, adjust antenna direction using browse keys.
Check the signal strength. Press OKkey to start the Automatic Channel Search
procedure.
You can see the progressive status of channel searching.
Please note that the Automatic Channel Searchprocedure may take a few minutes.
Press the menukey or exitkey to return to previous menu.
3. B. MANUAL CHANNEL SEARCH
It will be more convenient to use Manual Channel Searchprocedure when you want to
search channel for a specified transponder offered from the satellite. As in Automatic
Channel Search, Manual Channel Searchalso searches all channels broadcasted over
a specific transponder using its predefined information. You can add a new transponder if
you cannot find it on the predefined transponder list.
Select Manual Channel Searchmenu in Installationmenu, and the following screen
will be displayed.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Opentel ods 3000 ci set at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Opentel ods 3000 ci set in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Opentel ods 3000 ci set

Opentel ods 3000 ci set User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info