645308

Onkyo TX-SR702 Manual

80
Zoom out
Zoom in
Previous page
1/96
Next page
80
Controlling Other Components
You can use the AV Receiver’s remote controller (RC-
588M/RC-590M/RC-591M) to control your other com-
ponents, including those made by other manufacturers.
This chapter explains how to:
• Enter the remote control code for a component that
you want to control (e.g., DVD, TV, VCR).
• Learn commands directly from another component’s
remote controller (see page 88).
• Program the Macro function to perform a sequence of
actions with a single press of a button (see page 89).
Entering the appropriate remote control code for each
REMOTE MODE button will allow you to control your
other components with the remote controller. You’ll need
to perform this procedure for each component that you
want to control.
For the [DVD], [TV], [VCR], [CABLE], and [SAT] but-
tons, choose a code from the respective category. For the
[CD] and [MD/CDR] buttons, you can choose a code
from any category. Remote control codes cannot be
entered for the [RECEIVER] and [ZONE 2] buttons.
If the remote controller works OK, the code has been
entered correctly. If not, try again or try another code.
Codes for Onkyo DVD Players
The remote control code for an Onkyo DVD player
depends on whether it’s connected via , as follows:
5001:
Use this code if you’ve connected an cable
and an analog audio cable to your DVD player.
This is the default setting, so if you’re using
, you don’t need to change anything. Point
the remote controller at the AV receiver to
operate the DVD player.
5002:
Use this code if your DVD player doesn’t have
an jack, or you’re not using . Point the
remote controller at the DVD player to operate
it.
Setting the [MD/CDR] Button to CDR
By default, the [MD/CDR] button is set to control a
MiniDisc recorder. To control a CD recorder, it must be
set to CDR. The codes are as follows:
6002:
Code for controlling an CD recorder.
6003:
Code for controlling an MD recorder (default).
Entering Remote Control Codes
1
Look up the remote control code
for your component.
See “Remote Control Codes” on
page 82.
2
2
3
2
While holding down the REMOTE
MODE button that you want to
enter the code for, press the
[STANDBY] button.
3
Within 30 seconds, use the num-
ber buttons to enter the 4-digit
remote control code.
4
Select the remote controller
mode, point the remote control-
ler at the component, and check
its operation.
Remote controller buttons that can be
used in DVD mode are shown on
page 16. Those that can be used with
the TV, VCR, CABLE, and SAT modes
are shown on pages 86, 87.
STANDBY
TX-NR702,602_En.book Page 80 Monday, July 26, 2004 11:05 AM
… 80 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR702 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR702 in the language / languages: English as an attachment in your email.

The manual is 14,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR702

Onkyo TX-SR702 User Manual - French, Spanish - 190 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info