645324
94
Zoom out
Zoom in
Previous page
1/100
Next page
94
Troubleshooting—Continued
Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
On the TX-SR507, while Powered Zone 2 is being
used, nothing is output by these speakers (page 81).
The surround back speakers produce no sound
Depending on the current listening mode, no sound
may be produced by the surround back speakers. Try
another listening mode (page 59).
Not much sound may be produced by the surround
back speakers with some sources.
Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
On the TX-SR507, while Powered Zone 2 is being
used, playback in the main room is reduced to 2.1-
channels and the center, surround speakers produce no
sound (page 80).
On the TX-SR577, while Powered Zone 2 is being
used, playback in the main room is reduced to 5.1-
channels and the surround back speakers produce no
sound (page 80).
The subwoofer produces no sound
If the source material contains no audio in the LFE
channel, the subwoofer produces no sound.
Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
The Zone 2 speakers produce no sound
The Zone 2 speakers only output sources that are
connected to an analog input. Check to see if the
source component is connected to an analog input.
On the TX-SR577, “Powered Zone 2” cannot be used
if “Sp Type” is set to “Bi-Amp” (page 40).
There’s no sound with a certain signal format
Check the digital audio output setting on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
With some DVD-Video discs, you need to select an
audio format from a menu or with the [AUDIO] button
on your DVD player’s remote controller.
Can’t get 6.1- or 7.1-channel playback
On the TX-SR507, while Powered Zone 2 is being
used, playback in the main room is reduced to 2.1-
channels and the center, surround speakers produce no
sound (page 80).
On the TX-SR577, while Powered Zone 2 is being
used, playback in the main room is reduced to 5.1-
channels and the surround back speakers produce no
sound (page 80).
Can’t select the Pure Audio listening mode
The Pure Audio listening mode cannot be selected
while Zone 2 is on.
The Pure Audio listening mode is not available on the
North American / Taiwan models.
The volume cannot be set to 79
Check to see if a maximum volume has been set
(page 75).
If the volume level of each individual speaker has been
adjusted to high positive values (page 69), then the
maximum master volume possible may be reduced.
Note that the individual speaker volume levels are set
automatically after the Audyssey 2EQ™ Room Cor-
rection and Speaker Setup function has been com-
pleted (page 37).
After the Audyssey 2EQ™ Room Correction and
Speaker Setup function has been run, or the volume
level of each individual speaker has been adjusted
(pages 37 and 69), the maximum volume may be
reduced.
When the levels of each speaker have been adjusted
(page 69), the maximum possible volume may be
reduced.
Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and so on can degrade audio
performance, so don’t use them.
An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesn’t work
Make sure that the source is Dolby Digital (page 78).
About DTS signals
When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player may
produce a short audible noise. This is not a malfunction.
When DTS program material ends and the DTS
bitstream stops, the AV receiver remains in DTS
listening mode and the DTS indicator remains on. This
is to prevent noise when you use the pause, fast
forward, or fast reverse function on your player. If you
switch your player from DTS to PCM, as the AV
receiver does not switch formats immediately, you may
not hear anything, in which case you should stop your
player for about 3 seconds, and then resume playback.
With some CD players, you won’t be able to playback
DTS material properly even though your player is
connected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency
response changed) and the AV receiver doesn’t
recognize it as a genuine DTS signal. In such cases,
you may hear noise.
The beginning of audio received by an HDMI IN
can’t be heard
Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio
signals, sound may not be output immediately.
There’s no picture
Make sure that all video connecting plugs are pushed
in all the way (page 22).
Make sure that each video component is properly
connected.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
While the Pure Audio listening mode is selected, the
video circuitry is turned off and only the HDMI OUT
outputs video signals.
Video
94


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR507 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR507 in the language / languages: English as an attachment in your email.

The manual is 9,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR507

Onkyo TX-SR507 User Manual - German - 196 pages

Onkyo TX-SR507 User Manual - Dutch - 196 pages

Onkyo TX-SR507 User Manual - French - 200 pages

Onkyo TX-SR507 User Manual - Italian - 196 pages

Onkyo TX-SR507 User Manual - Swedish - 196 pages

Onkyo TX-SR507 User Manual - Spanish - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info