645324
93
Zoom out
Zoom in
Previous page
1/100
Next page
93
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact your Onkyo dealer.
Can’t turn on the AV receiver
Make sure that the power cord is plugged into the wall
outlet properly.
Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it back in again.
The AV receiver turns off as soon as it’s turned
on
The amp protection circuit has been activated.
Remove the power cord from the wall outlet
immediately. Disconnect all speaker cables and input
sources, and leave the AV receiver with its power cord
disconnected for 1 hour. After that, reconnect the
power cord and set the volume to maximum. If the AV
receiver stays on, set the volume to minimum,
disconnect the power cord, and reconnect your
speakers and input sources. If the AV receiver turns off
when you set the volume to maximum, disconnect the
power cord, and contact your Onkyo dealer.
There’s no sound or it’s very quiet
To listen to an audio source that’s connected to an
HDMI input, make sure that input is assigned to an
input selector (page 41).
To listen to an audio source that’s connected to an
OPTICAL or COAXIAL input, make sure that input is
assigned to an input selector (page 43).
Make sure that all audio connecting plugs are pushed
in all the way (page 22).
Make sure that the polarity of the speaker cables is
correct, and that the bare wire is in contact with the
metal part of each speaker terminal (page 17).
Make sure that the speaker cables are not shorting.
Check the volume (page 45). The AV receiver is
designed for home theater enjoyment and has a wide
volume range for precise adjustment.
If the MUTING indicator is flashing on the display,
press the remote controller’s [MUTING] button to
unmute the AV receiver (page 46).
While a pair of headphones is connected to the
PHONES jack, no sound is output by the speakers
(page 47).
Check the digital audio output settings on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
With some DVD-Video discs, you need to select an
audio format from a menu or with the [AUDIO] button
on your DVD player’s remote controller.
If your turntable doesn’t have a phono preamp built-in,
you must connect one between it and the AV receiver.
If your turntable uses an MC cartridge, you must
connect an MC head amp, or an MC transformer and
a phono preamp.
Check the speaker settings (pages 66–70).
If the digital signal format is set to PCM or DTS, set it
to “Auto” (page 48).
If there’s no sound from a DVD player connected to an
HDMI IN, check the DVD player’s output settings,
and be sure to select a compatible audio format.
Only the front speakers produce sound
When the DTS Surround Sensation, Stereo or Mono
listening mode is selected, only the front speakers and
subwoofer produce sound.
Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
Only the center speaker produces sound
If you use the Dolby Pro Logic IIx Movie or Dolby Pro
Logic IIx Music listening mode with a mono source,
such as an AM radio station or mono TV program, the
sound will be concentrated in the center speaker.
Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
The center speaker produces no sound
When the DTS Surround Sensation, Stereo or Mono
listening mode is selected, the center speaker produces
no sound (page 64).
Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
On the TX-SR507, while Powered Zone 2 is being
used, nothing is output by these speakers (page 81).
The surround speakers produce no sound
When the DTS Surround Sensation, T-D (Theater-
Dimensional), Stereo or Mono listening mode is
selected, the surround speakers produce no sound.
Depending on the source and the current listening
mode, not much sound may be produced by the
surround speakers. Try another listening mode
(page 59).
Power
Audio
If you can’t resolve the issue yourself, try resetting
the AV receiver before contacting your Onkyo
dealer.
To reset the AV receiver to its factory defaults,
turn it on and, while holding down the [VCR/DVR]
button, press the [ON/STANDBY] button. “Clear”
will appear on the display and the AV receiver will
enter Standby mode.
Note that resetting the AV receiver will delete your
radio presets and custom settings.
93


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR507 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR507 in the language / languages: English as an attachment in your email.

The manual is 9,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR507

Onkyo TX-SR507 User Manual - German - 196 pages

Onkyo TX-SR507 User Manual - Dutch - 196 pages

Onkyo TX-SR507 User Manual - French - 200 pages

Onkyo TX-SR507 User Manual - Italian - 196 pages

Onkyo TX-SR507 User Manual - Swedish - 196 pages

Onkyo TX-SR507 User Manual - Spanish - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info