645312
57
Zoom out
Zoom in
Previous page
1/60
Next page
57
Troubleshooting
—Continued
Symptom Possible cause Remedy
Audio
The surround back speak-
ers produce no sound?
The level of the surround back speaker is set
at minimum.
Check the volume of the surround back
speaker (page 49).
The Surround Back setting is set to None in
the Speaker Configuration.
Check the Surround Back setting in the
Speaker Configuration (page 32).
The selected listening mode doesn’t use the
surround back speakers.
Select another listening mode. See page 42
for information on listening modes.
Surround speaker output depends on the
source material, and some material may not
use the surround speakers much.
If you’re playing a Dolby Digital EX or
DTS-ES source, make sure that the Dolby
Digital/DTS setting is set to On (page 44).
A low-frequency noise or
hum can be heard?
The audio connecting cables at the rear of
the TX-SR502/TX-SR502E are too close to
the power cord.
Untangle the audio cables and position them
as far away as possible from the power cord.
The sound is too bright or
harsh and the high range is
not clear?
The treble is set too high. Adjust the treble (page 38).
The subwoofer is not work-
ing or is very quiet?
The Subwoofer setting is set to No in the
Speaker Configuration.
Check the Subwoofer setting in the Speaker
Configuration (page 32).
The volume of the subwoofer is set at mini-
mum.
Check the volume of the subwoofer
(page 49, 35).
Speaker set A is turned off. The subwoofer
output does not work while only speaker set
B is on.
Turn on speaker set A.
Video
There’s no picture on the
TV?
The Pure Audio listening mode is selected.
When this mode is selected, the display and
the internal video circuits are all turned off
and no video signals are output.
The TV’s input selector is set incorrectly.
Select the correct input on the TV (i.e., the
input to which the TX-SR502/TX-SR502E is
connected).
The video input and output are different for-
mats.
The TX-SR502/TX-SR502E doesn’t convert
between video formats. It works as a video
signal switcher. Composite video input sig-
nals are output only by composite video out-
puts. S-Video input signals are output only
by S-Video outputs. And component video
input signals are output only by component
video outputs.
Remote controller
The buttons on the
TX-SR502/TX-SR502E work
OK but those on the remote
controller don’t?
The wrong remote controller mode is
selected.
Select the correct mode (page 10).
The batteries are installed incorrectly.
Check the batteries and correct as necessary
(page 9).
You’re not pointing the remote controller at
the TX-SR502/TX-SR502Es remote sensor.
Point the remote controller at the TX-SR502/
TX-SR502E’s remote sensor (page 9).
Can’t use the remote con-
troller with other AV com-
ponents?
You’ve connected a MiniDisc recorder or
CD recorder to the TX-SR502/TX-SR502E
but haven’t changed the TAPE/MD/CDR
display.
Press and hold the [TAPE] input selector
button until MD or CDR, as appropriate,
appears on the display.
The wrong remote control code has been
entered.
If more than one code is listed, try each one
(page 50).
With some AV components, certain buttons
may not work as expected and some may not
work at all.
You’re pointing the remote controller at the
wrong AV component.
To control a component connected via ,
point the remote controller at the TX-SR502/
TX-SR502E. To control a component that’s
not connected via , point the remote con-
troller at that component (page 50)
You’ve made an connection but not an
analog audio connection (RCA).
To use , you must make an connection
and an analog audio connection (RCA)
between the component and TX-SR502/
TX-SR502E, even if they are connected dig-
itally (page 30).
TX-SR502_En.book Page 57 Tuesday, February 17, 2004 12:14 PM
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR502 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR502 in the language / languages: English as an attachment in your email.

The manual is 5,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR502

Onkyo TX-SR502 User Manual - German, Dutch - 236 pages

Onkyo TX-SR502 User Manual - French - 120 pages

Onkyo TX-SR502 User Manual - Italian, Swedish - 236 pages

Onkyo TX-SR502 User Manual - Spanish - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info