❏Cannot ZONE B-output the audio of externally connected AV components
• To output audio to ZONE B, set the audio output destination to "ZONE A+B" or "ZONE B".( p46)
Remote Controller
• Make sure that the batteries are inserted with the correct polarity.
• Insert new batteries. Do not mix different types of batteries, or old and new batteries.
• Make sure that the sensor of the main unit is not subjected to direct sunlight or inverter-type uorescent lights. Relocate it if necessary.
• If the main unit is installed in a rack or cabinet with colored-glass doors, or if the doors are closed, the remote controller may not work normally.
Display
❏The display does not light up
• When the Dimmer function is working, the display may go dim. Press the DIMMER button, and change the brightness level of the display.( p9)
Others
❏Strange noise can be heard from the unit
• If you have connected another device to the same outlet as this unit, strange noise may occur under the inuence of the device. If the symptom is
remedied by removing the power plug of the other device from the outlet, use different outlets for this unit and the device.
❏The message "Noise Error" appears during AccuEQ Room Calibration
• This can be caused by a malfunction in your speaker unit. Check the speaker output, etc.
❏The measurement results of AccuEQ Room Calibration show different distances to the speakers from
the actual ones
• Depending on the speakers you are using, some errors may occur in the measurement results. If this is the case, make the settings in
"2. Speaker" - "Distance" in the Setup menu.
( p74)
❏The measurement results of AccuEQ Room Calibration show that the volume level of the subwoofer
has been corrected to the lower limit
• The volume level correction of the subwoofer may not have been completed. Lower the volume of the subwoofer before AccuEQ Room
Calibration measurement.
❏The POWER OUT jack cannot supply power to smart phones/tablets or other devices
• The POWER OUT jack on the rear panel is only intended to supply power (5 V/1 A) to the Streaming media player connected to HDMI IN jack of
this unit with a USB cable. It cannot supply power to smart phones/tablets or other devices.
I have connected my Onkyo receiver to my projector thru the HDMI out but have received the message "signal out of reach". My TV which is close to the av receiver works ok when using the HDMI out. The projector is on the ceiling in line with the ceiling speakers and they work Ok when the tv is used, How do I correct this?
Submitted on 6-1-2024 at 06:37
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Onkyo TX-SR494 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Onkyo TX-SR494 in the language / languages: English as an attachment in your email.
The manual is 4,64 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
