686346
73
Zoom out
Zoom in
Previous page
1/102
Next page
73
Bedienfeld Rückseite Fernbedienung
Inhalt
Verbindungen
Wiedergabe
Einrichtung
2. Speaker
1. Conguration
Wählen Sie die Einstellungen der Anschlussumgebung der Lautsprecher.
Einstellpunkt Standardwert Einstelldetails
Speaker
Channels
7.1 ch Wählen Sie je nach Anzahl der angeschlossenen
Lautsprecherkanäle "2.1 ch", "3.1 ch", "4.1 ch", "5.1
ch", "6.1 ch", "7.1 ch", "2.1.2 ch", "3.1.2 ch", "4.1.2
ch" oder "5.1.2 ch" aus.
Subwoofer Yes Stellt ein, ob ein Subwoofer angeschlossen ist oder
nicht.
"Yes": Wenn ein Subwoofer angeschlossen ist
"No": Wenn kein Subwoofer angeschlossen ist
Height Speaker Top Middle Legen Sie den Lautsprechertyp fest, wenn
Höhenlautsprecher an die SURROUND BACK-
oder HEIGHT-Klemmen angeschlossen sind.
Wählen Sie "Top Middle", "Top Rear", "Rear High",
"Dolby Speaker (Front)", "Dolby Speaker (Surr)",
"Front High" oder "Top Front" entsprechend dem Typ
und dem Layout der angeschlossenen Lautsprecher.
• Wenn eine Option nicht gewählt werden kann,
obwohl die Verbindung korrekt ist, überprüfen
Sie, ob die Einstellungen in "Speaker Channels"
der Anzahl der angeschlossenen Kanäle
entspricht.
Zone B Speaker No Wenn Lautsprecher an die
Zone B-Lautsprecherklemmen angeschlossen sind.
"Yes": Wenn Lautsprecher an die
Zone B-Lautsprecherklemmen angeschlossen sind
"No": Wenn keine Lautsprecher an die
Zone B-Lautsprecherklemmen angeschlossen sind
Einstellpunkt Standardwert Einstelldetails
Zone B Output
Level
Fixed Wählen Sie aus, ob die Lautstärke am
Vorverstärker im separaten Raum oder an diesem
Gerät geregelt werden soll, wenn die Wiedergabe
in Zone B erfolgt.
"Fixed": Die Regelung erfolgt über den
Vorverstärker im separaten Raum
"Variable": An diesem Gerät anpassen
• Die Einstellung ist auf "Variable" festgelegt, wenn
"Zone B Speaker" auf "Yes" eingestellt ist.
Bi-Amp No Legen Sie die Einstellung für einen Bi-Amp-
Anschluss der Frontlautsprecher fest.
"No": Wenn Frontlautsprecher nicht über Bi-Amp
angeschlossen sind
"Yes": Wenn Frontlautsprecher über Bi-Amp
angeschlossen sind
• Die Einstellung ist fest auf "No" gestellt, wenn
"Zone B Speaker" auf "Yes" gestellt ist.
• Diese Einstellung kann nicht ausgewählt werden,
wenn Surround-Back- oder Höhenlautsprecher
angeschlossen sind.
Speaker
Impedance
6 ohms or above Stellen Sie die Impedanz (Ω) der angeschlossenen
Lautsprecher ein.
"4 ohms": Wenn einer der angeschlossenen
Lautsprecher eine Impedanz zwischen 4 Ω und 6 Ω
aufweist
"6 ohms or above": Wenn alle angeschlossenen
Lautsprecher eine Impedanz von mindestens 6 Ω
aufweisen
• Prüfen Sie für die Impedanz die Angaben auf
der Rückseite der Lautsprecher oder deren
Bedienungsanleitung.
73


Need help? Post your question in this forum.

Forumrules
1

Forum

onkyo-tx-sr494

Reset search

  • I have connected my Onkyo receiver to my projector thru the HDMI out but have received the message "signal out of reach". My TV which is close to the av receiver works ok when using the HDMI out. The projector is on the ceiling in line with the ceiling speakers and they work Ok when the tv is used,
    How do I correct this? Submitted on 6-1-2024 at 06:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR494 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR494 in the language / languages: German as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR494

Onkyo TX-SR494 User Manual - English - 100 pages

Onkyo TX-SR494 User Manual - Dutch - 101 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info