517568
85
Zoom out
Zoom in
Previous page
1/160
Next page
Advanced Operations
En-85
Adjusting the Volume for Zones
Operating on the remote controller
Operating on the AV receiver
If your Zone 2/3 speakers are connected to a receiver
or integrated amplifier in Zone 2/3, use its volume
control to adjust the volume.
Muting Zones
Operating on the remote controller
Tip
To unmute, press ZONE followed by MUTING again. Zones
can also be unmuted by adjusting the volume.
Note
ZONE 2 LINE OUT and ZONE 2 L/R output 2ch PCM,
analog, NET or USB input sources. To listen to the PCM
source, you need to make an HDMI connection.
Only analog, NET or USB input source is output from the
ZONE 3 LINE OUT jacks and ZONE 3 L/R terminals.
You cannot select different AM or FM radio stations for your
main room and Zone 2/3. The same AM/FM radio station
will be heard in each room. Namely, if you have selected an
FM station for the main room, that station will also be output
in Zone 2/3.
If an HDMI component selected in Zone 2 outputs the
sound other than PCM, the sound is not output from
ZONE 2 L/R and ZONE 2 LINE OUT.
Both audio and video outputs from an HDMI component
may interrupt when the main room and Zone 2 are set to
share the same source or not.
You cannot select different input selector NET or USB for
your main room and Zone 2/3. Namely, if you have selected
USB input selector for Zone 2/3, USB input selector will be
selected in main room even if NET has been selected for
main room.
•“BLUETOOTH” cannot be selected as input selector in
Multi Zone. If you play audio from Bluetooth-enabled device
in Multi Zone, select “Zone 2 Selector: Source” or “Zone 3
Selector: Source”, and “BLUETOOTH” as input selector in
Main room.
When Zone 2/3 is activated and its input selector is
selected, the power consumption of standby mode slightly
increases.
While Zone 2/3 is on, u functions will not work.
The component connected to HDMI input other than HDMI
IN 1/2/3/AUX INPUT is selected as an input source for
Zone 2, the linked operations of p may not work
properly. In this case, set the linked operations to Off on the
source component.
When setting the AV receiver to standby mode while Zone
2/3 is active, the Z2 or Z3 indicator is dimly lit.
Activating Zones in the main room when the listening mode
is set to Pure Audio will automatically switch it to Direct.
•“GAME2” cannot be selected as input sources for Zone 3.
When “GAME2” is the input source of Main room and
Zone 3 is set to share the same source, no sound will be
output from Zone 3.
Even if you repeatedly press the remote controller’s ZONE
to select zones, the last zone selection will be retained once
you have switched to other components by pressing other
REMOTE MODE after pressing ZONE.
1
Press ZONE repeatedly, then point the remote
controller at the AV receiver and press
8RECEIVER.
Zone 2/3 turns on, the Z2 or Z3 indicator lights on
the AV receiver’s display.
Tip
The corresponding trigger output goes high (+12 V).
2
To select an input source for Zone 2/3, press
ZONE repeatedly, followed by an INPUT
SELECTOR button.
To select AM or FM, press ZONE and the TUNER
input selector repeatedly.
3
To turn off Zone 2/3, press ZONE repeatedly,
followed by 8RECEIVER.
The zone is turned off.
Tip
The corresponding trigger output goes low (0 volts).
1
Press ZONE repeatedly.
2
Use VOL q/w.
1
Press ZONE 2 or ZONE 3 (the Z2/Z3 indicator
on the AV receiver’s display flashes).
2
Use MASTER VOLUME control within 8
seconds.
1
Press ZONE repeatedly, and then press
MUTING.
85


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR929 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR929 in the language / languages: English as an attachment in your email.

The manual is 4,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR929

Onkyo TX-NR929 Quick start guide - English - 4 pages

Onkyo TX-NR929 Quick start guide - German - 4 pages

Onkyo TX-NR929 User Manual - German - 160 pages

Onkyo TX-NR929 Quick start guide - Dutch - 4 pages

Onkyo TX-NR929 User Manual - Dutch - 160 pages

Onkyo TX-NR929 User Manual - French - 160 pages

Onkyo TX-NR929 User Manual - French - 4 pages

Onkyo TX-NR929 User Manual - Italian - 156 pages

Onkyo TX-NR929 Quick start guide - Italian - 4 pages

Onkyo TX-NR929 User Manual - Swedish - 160 pages

Onkyo TX-NR929 Quick start guide - Swedish - 4 pages

Onkyo TX-NR929 User Manual - Spanish - 160 pages

Onkyo TX-NR929 Quick start guide - Spanish - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info