62439
144
Zoom out
Zoom in
Previous page
1/150
Next page
144
Troubleshooting—Continued
If your TV is connected to the HDMI output, set the
“Monitor Out” setting to “HDMI Main” or “HDMI
Sub” (page 52), and select “- - -” in the “Video Input
Setup” on page 56 to watch composite video, S-Video,
and component video sources.
If your TV is connected to the COMPONENT VIDEO
MONITOR OUT, set the “Monitor Out” setting to
“Analog” (page 52), and select “- - -” in the “Compo-
nent Video Setup” on page 58 to watch composite
video and S-Video sources.
If the video source is connected to a component video
input, you must assign that input to an input selector
(page 58), and your TV must be connected to either
the HDMI OUT or COMPONENT VIDEO MONI-
TOR OUT (pages 36 and 42).
If the video source is connected to an HDMI input,
you must assign that input to an input selector
(page 56), and your TV must be connected to the
HDMI OUT (page 42).
There’s no picture from a source connected to
an HDMI IN
When the “Monitor Out” setting is set to “Analog”,
and the “Resolution” setting is set to anything other
than “Through” (see page 55), no video is output by
the HDMI OUT.
If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that your TV does not
support the current video resolution and you need to
select another resolution on your DVD player.
The onscreen menus don’t appear
If your TV is connected to the analog outputs, set the
“Monitor Out” setting to “Analog” (page 52).
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
On non-North American models, specify the TV system
used in your area in the “TV Format Setup
(not North American models)” on page 62.
The immediate display does not appear
The immediate display will not appear when the input
signal from the COMPONENT VIDEO IN is output to
a device connected to the COMPONENT VIDEO
MONITOR OUT.
Depending on the input signal, the immediate display
may not appear when the input signal from the HDMI
IN is output to a device connected to the HDMI OUT.
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t
appear
Relocate your antenna.
Move the AV receiver away from your TV or computer.
Listen to the station in mono (page 73).
When listening to an AM station, operating the remote
controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
Make sure that the batteries are installed with the cor-
rect polarity (page 15).
Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor (page 15).
Make sure you’ve selected the correct remote control-
ler mode (page 16).
Make sure you’ve entered the correct remote control
code (page 137).
Install new batteries. Don’t mix different types of bat-
teries, or old and new batteries (page 15).
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not work
reliably when the doors are closed.
When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
Make sure to set the same ID on both the AV receiver
and remote controller (page 117).
Can’t control other components
If it’s an Onkyo component, make sure that the u
cable and analog audio cable are connected properly.
Connecting only an u cable won’t work (page 50).
Make sure you’ve selected the correct remote control-
ler mode (page 16).
If you’ve connected an u-capable Onkyo MD
recorder, CD recorder, u Dock to the TAPE IN/OUT
jacks, or an u Dock to the AUX 1 jacks, for the
remote controller to work properly, you must set the
display to MD, CDR, or DOCK (page 63).
If you cannot operate it, you will need to enter the
appropriate remote control code (page 137).
The entered remote control code may not be correct. If
more than one code is listed, try each one.
If none of the codes work, use the Learning function
to learn the commands of the other component’s
remote controller (page 140).
With some AV components, certain buttons may not
work as expected, and some may not work at all.
To control an Onkyo component that’s connected via
u, point the remote controller at the AV receiver. Be
sure to enter the appropriate remote control code first
(page 138).
Tuner
Remote Controller
144


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR906 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR906 in the language / languages: English as an attachment in your email.

The manual is 7,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR906

Onkyo TX-NR906 User Manual - German - 294 pages

Onkyo TX-NR906 User Manual - Dutch - 294 pages

Onkyo TX-NR906 User Manual - Italian - 294 pages

Onkyo TX-NR906 User Manual - Swedish - 294 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info