62439
143
Zoom out
Zoom in
Previous page
1/150
Next page
143
Troubleshooting—Continued
The surround back speakers produce no sound
The surround back speakers are not used with all lis-
tening modes. Select another listening mode (page 81).
Not much sound may be produced by the surround
back speakers with some sources.
Make sure the speakers are configured correctly (page 95).
While Powered Zone 2 is being used, playback in the
main room is reduced to 5.1-channels and the sur-
round back speakers produce no sound (page 130).
The subwoofer produces no sound
When you play source material that contains no infor-
mation in the LFE channel, the subwoofer produces
no sound.
Make sure the speakers are configured correctly (page 95).
The Zone 2/3 speakers produce no sound
The Zone 2/3 speakers only output sources that are
connected to an analog input. Check to see if the
source component is connected to an analog input.
Powered Zone 2 cannot be used if “Speaker Type:
Front(Speaker A)” is set to “Bi-Amp” or “BTL”, or
“Speaker Type: Front(Speaker B)” is set to “Normal”,
“Bi-Amp”, or “BTL” (page 61).
There’s no sound with a certain signal format
Check the digital audio output setting on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
With some DVD-Video discs, you need to select an
audio format from a menu or with the [AUDIO] button
on your DVD player’s remote controller.
Depending on the input signal, some listening modes
cannot be selected (pages 82-86).
Can’t get 6.1- or 7.1-channel playback
While Powered Zone 2 is being used, playback in the
main room is reduced to 5.1-channels and the sur-
round back speakers produce no sound (page 130).
Can’t select the Pure Audio listening mode
The Pure Audio listening mode cannot be selected
while Zone 2 is on.
The volume cannot be set as required (The vol-
ume cannot be set to +18.0 dB)
Check to see if a maximum volume has been set
(page 115).
After the Automatic Speaker Setup function has been
run, or the volume level of each individual speaker has
been adjusted (pages 71 and 100), the maximum vol-
ume may be reduced.
Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and so on can degrade audio
performance, so don’t use them.
An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesn’t work
Make sure the source material is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD (page 109).
The DVD analog multichannel input doesn’t
work
Check the DVD multichannel input connections
(page 120).
Make sure that the multichannel input is assigned to
the input selector (page 60).
Make sure that the multichannel input is selected
(page 80).
Make sure that the “Speaker Type” is not set to
“Bi-Amp”. The multichannel DVD input cannot be
used if “Speaker Type” is set to “Bi-Amp” (page 61).
Check the audio output settings on your DVD player.
About DTS signals
When DTS program material ends and the DTS bit-
stream stops, the AV receiver remains in DTS listening
mode and the DTS indicator remains on. This is to pre-
vent noise when you use the pause, fast forward, or fast
reverse function on your player. If you switch your
player from DTS to PCM, because the AV receiver does
not switch formats immediately, you may not hear any
sound, in which case you should stop your player for
about three seconds, and then resume playback.
With some CD players, you won’t be able to playback
DTS material properly even though your player is
connected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency
response changed) and the AV receiver doesn’t recog-
nize it as a genuine DTS signal. In such cases, you
may hear noise.
When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a mal-
function.
The beginning of audio received by an HDMI IN
can’t be heard
Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio sig-
nals, sound may not be output immediately.
There’s no picture
Make sure that all video connecting plugs are pushed
in all the way (page 33).
Make sure that each video component is properly con-
nected (pages 36-49).
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
While the Pure Audio listening mode is selected, the
video circuitry is turned off and only video signals
input through HDMI IN can be output.
Video
143


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR906 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR906 in the language / languages: English as an attachment in your email.

The manual is 7,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR906

Onkyo TX-NR906 User Manual - German - 294 pages

Onkyo TX-NR906 User Manual - Dutch - 294 pages

Onkyo TX-NR906 User Manual - Italian - 294 pages

Onkyo TX-NR906 User Manual - Swedish - 294 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info