645307
92
Zoom out
Zoom in
Previous page
1/100
Next page
92
En
The u functions don’t work
The functions System On/Auto Power On and
Direct Change don’t work for components
connected via u
When performing “Audyssey MultEQ
®
Room
Correction and Speaker Setup”, the
measurement fails showing the message
“Ambient noise is too high.”.
The following settings can be made for the
S-Video and composite video inputs
You must use the buttons on the unit to make these set-
tings.
1. While holding down the input selector button for the input
source that you want to set, press SETUP.
2. Use e/r to change the setting.
3. Press the input selector button for the input source that you
want to set when you’ve finished.
Video Attenuation
This setting can be made for the BD/DVD, VCR/DVR,
CBL/SAT, GAME, or AUX input.
If you have a games console connected to the composite
video input, and the picture isn’t very clear, you can
attenuate the gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain reduced by 2dB.
The AV receiver can upconvert component video, S-
Video, and composite video sources for display on a TV
connected to the HDMI output. However, if the picture
quality of the source is poor, upconversion may make the
picture worse or disappear altogether.
In this case, try the following:
Note
•IfMonitor Out” setting is set to “Analog”, press VCR/DVR
and RETURN on the AV receiver at the same time. Select
Skip” in the “VideoProcessor” setting on the display. To reset
back to the original setting, press the same button at the same
time. If you select “Use”, the AV receiver will output video sig-
nals from the video processor.
To use u, you must make an u connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected dig-
itally.
20
These functions don’t work when Zone 2/3 is turned
on.
20
This can be caused by any malfunction in your
speaker unit. Check if the unit produces normal
sounds.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
Important Note Regarding Video Playback
1
If the video source is connected to a component
video input, connect your TV to the COMPO-
NENT VIDEO MONITOR OUT.
If the video source is connected to an S-Video input,
connect your TV to a MONITOR OUT S.
If the video source is connected to a composite video
input, connect your TV to MONITOR OUT V.
2
On the main menu, select “Input/Output Assign”,
and then select “HDMI Input”.
Select the relevant input selector, and assign it to
----- ( 43).
3
On the main menu, select “Input/Output Assign”,
and then select “Component Video Input” ( 44):
If the video source is connected to COMPO-
NENT VIDEO IN 1, select the relevant input
selector, and assign it to “IN1”.
If the video source is connected to COMPO-
NENT VIDEO IN 2, select the relevant input
selector, and assign it to “IN2”.
If the video source is connected to an S-Video
input or composite video input, select the relevant
input selector, and assign it to “-----”.
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR808 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR808 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR808

Onkyo TX-NR808 User Manual - German - 196 pages

Onkyo TX-NR808 User Manual - Dutch - 196 pages

Onkyo TX-NR808 User Manual - French - 200 pages

Onkyo TX-NR808 User Manual - Italian - 196 pages

Onkyo TX-NR808 User Manual - Swedish - 196 pages

Onkyo TX-NR808 User Manual - Spanish - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info