645307
72
Zoom out
Zoom in
Previous page
1/100
Next page
72
En
Note
This procedure can also be performed on the AV receiver by
using SETUP, arrows, and ENTER.
Zone2 Out, Zone3 Out
` Fixed
:
The Zone 2/3 volume must be set on the amp in that
zone.
` Variable:
The Zone 2/3 volume can be set on the AV receiver.
If you’ve connected your Zone 2/3 speakers to an amp
with no volume control, set the “Zone2 Out” and “Zone3
Out” setting, respectively, to “Variable” so that you can
set the volume, balance, and tone of zone 2 and volume
and balance of zone 3 on the AV receiver.
Zone2 Maximum Volume,
Zone3 Maximum Volume
` Off
, 50 to 99 (Absolute display)
` Off
, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume for
Zone 2/3.
Zone2 Power On Volume,
Zone3 Power On Volume
` Last
, Min, 1 to 99 or Max (Absolute display)
` Last
, QdB, –81dB to +18dB (Relative display)
This setting determines what the volume will be for
Zone 2/3 each time the AV receiver is turned on.
To use the same volume level as when the AV receiver was
last turned off, select “Last”.
The “Zone2 Power On Volume” and “Zone3 Power On
Volumecannot be set higher than the “Zone2 Maximum
Volume” and “Zone3 Maximum Volume” setting.
This section explains how to turn Zone 2/3 on and off,
how to select an input source for Zone 2/3, and how to
adjust the volume for Zone 2/3.
Controlling Zone 2/3 from the AV receiver
Note
When Zone 2/3 is turned off, the output from the ZONE 2/3
12V TRIGGER OUT goes low (0 volts).
Setting the Multi Zone
1
Press RECEIVER followed by SETUP.
The main menu appears onscreen.
Tip
If the main menu doesn’t appear, make sure the appropri-
ate external input is selected on your TV.
2
Use q/w to select “Hardware Setup”, and then
press ENTER.
The “Hardware Setup” menu appears.
3
Use q/w to select “Multi Zone”, and then press
ENTER.
The “Multi Zone” menu appears.
4
Use q/w to select an item, and use e/r to change
it.
The items are explained below.
5
Press SETUP.
The setup menu closes.
7. Hardware Setup
1. Remote ID
2. Multi Zone
3. Tuner
4. HDMI
5. Auto Power Down
6. Network
7. Firmware Update
7-2. Multi Zone
Zone2 Out
Zone2 Maximum Volume
Zone2 Power On Volume
Zone3 Out
Zone3 Maximum Volume
Zone3 Power On Volume
Fixed
Off
Last
Fixed
Off
Last
Using Zone 2/3
1
To turn on Zone 2/3 and select an input source,
press ZONE 2 or ZONE 3 followed by an input
selector button within 8 seconds.
Zone 2/3 turns on, the ZONE 2/3 indicator lights.
Tip
ZONE 2/3 12V TRIGGER OUT goes high (+12 V).
To select AM or FM, press TUNER input selector
and ZONE 2 or ZONE 3 repeatedly.
(North American models) You can also select SIR-
IUS.
To select the same source as that of the main room,
press ZONE 2 or ZONE 3 twice. “Zone 2 Selector:
Source” or “Zone 3 Selector: Source” appears on
the display.
2
To turn off Zone 2/3, press ZONE 2 or ZONE 3.
ZONE 2 or ZONE 3 indicator flashes.
Press OFF.
The zone is turned off, and the ZONE 2 or ZONE 3
indicator goes off.
ZONE 3
ZONE 2
OFF
ZONE 2 indicator
ZONE 3 indicator
Input selector buttons
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR808 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR808 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR808

Onkyo TX-NR808 User Manual - German - 196 pages

Onkyo TX-NR808 User Manual - Dutch - 196 pages

Onkyo TX-NR808 User Manual - French - 200 pages

Onkyo TX-NR808 User Manual - Italian - 196 pages

Onkyo TX-NR808 User Manual - Swedish - 196 pages

Onkyo TX-NR808 User Manual - Spanish - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info