645307
71
Zoom out
Zoom in
Previous page
1/100
Next page
71
En
Connecting Your Zone 3 Speakers to an
Amp in Zone 3
This setup allows 7.1-channel playback in your main lis-
tening room and 2-channel stereo playback in Zone 3,
with a different source in each room.
Note
With the default settings, the Zone 3 volume must be set on the
Zone 3 amp. If your Zone 3 amp has no volume control, set the
Zone3 Out” setting to “Variable ” so that you can set the
Zone 3 volume on the AV receiver ( 72).
Zone 3 12V Trigger
When Zone 3 is turned on, the output from the ZONE 3
12V TRIGGER OUT goes high (+12 volts, 25 milliam-
peres max). Connecting this jack to a 12-volt trigger input
on a component in Zone 3 will make that component turn
on or off as and when Zone 3 is turned on or off on the AV
receiver.
If you’ve connected your Zone 2 speakers to the AV
receiver, as explained in “Connecting Your Zone 2 Speak-
ers Directly to the AV receiver” ( 70), you must set the
Powered Zone2” setting to “Act” (Activated).
Note
Powered Zone 2 cannot be used if “Speakers Type(Front)” is
set to “Bi-Amp” ( 45).
This procedure can also be performed on the AV receiver by
using SETUP, arrows, and ENTER.
Connecting Zone 3
Hookup
Use an RCA audio cable to connect the AV receiver’s
ZONE 3 PRE OUT L/R jacks to an analog audio input on
your Zone 3 amp.
Connect your Zone 3 speakers to the speaker terminals on
your Zone 3 amp.
R
L
IN
Main room
TV
Zone 3
AV receiver
Receiver/
integrated amp
Setting the Powered Zone 2
1
Press RECEIVER followed by SETUP.
The main menu appears onscreen.
Tip
If the main menu doesn’t appear, make sure the appropri-
ate external input is selected on your TV.
2
Use q/w to select “Speaker Setup”, and then press
ENTER.
The “Speaker Setup” menu appears.
3
Use q/w to select “Speaker Settings”, and then
press ENTER.
The “Speaker Settings” menu appears.
4
Use q/w to select “Powered Zone2”, and use e/r
to select:
` Not Act:
Use FRONT WIDE/ZONE 2 L/R terminals to
connect front wide speakers. (Powered Zone 2
disabled.)
` Act:
Use FRONT WIDE/ZONE 2 L/R terminals to
connect Zone 2 speakers. (Powered Zone 2
enabled.)
5
Press SETUP.
The setup menu closes.
2. Speaker Setup
1. Speaker Settings
2. Speaker Configuration
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
2–1. Speaker Settings
Speaker Impedance
Speakers Type(Front)
Powered Zone2
6ohms
Normal
Not Act
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR808 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR808 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR808

Onkyo TX-NR808 User Manual - German - 196 pages

Onkyo TX-NR808 User Manual - Dutch - 196 pages

Onkyo TX-NR808 User Manual - French - 200 pages

Onkyo TX-NR808 User Manual - Italian - 196 pages

Onkyo TX-NR808 User Manual - Swedish - 196 pages

Onkyo TX-NR808 User Manual - Spanish - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info