645307

Onkyo TX-NR808 Manual

46
Zoom out
Zoom in
Previous page
1/100
Next page
46
En
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your speak-
ers using Audyssey MultEQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to “80Hz(THX)” crossover.
■ Subwoofer
` Ye s
:
Select if a subwoofer is connected.
` No:
Select if no subwoofer is connected.
■ Front
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz,
200Hz
Note
•If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■ Center
*1
, Surround
*1
, Surr Back
*2*3*4*5
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz,
200Hz
` None:
Select if no speaker is connected.
■ Front Wide
*1*2*4*6
, Front High
*1*2*4*5
` Full Band
` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
` None
:
Select if no speaker is connected.
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*3
If the “Surround” setting is set to anything other than “Full
Band”, “Full Band” cannot be selected here.
*4
If the “Speakers Type(Front)” setting is set to “Bi-Amp”
(➔ 45), this setting cannot be selected.
*5
If the Powered Zone 2 is being used (➔ 71), this setting can-
not be selected.
*6
If the “Powered Zone 2” setting is set to “Act” (➔ 71), this
setting cannot be selected.
■ Surr Back Ch
` 1ch:
Select if only one surround back speaker is con-
nected.
` 2ch
:
Select if two (left and right) surround back speakers
are connected.
Note
•If the “Surr Back” setting is set to “None” (➔ 46), this setting
cannot be selected.
■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
` 80Hz, 90Hz, 100Hz, 120Hz
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
■ Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
` On:
Double Bass function on.
` Off(THX):
Double Bass function off.
Note
• This function can be set only if the “Subwoofer” setting is set to
“Ye s”, and the “Front” setting is set to “Full Band”.
• If you’re using THX-certified speakers, select “Off(THX)”.
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
■ Unit
` feet:
Distances can be set in feet. Range: “0.5ft” to
“30.0ft” in 0.5 foot steps.
` meters:
Distances can be set in meters. Range: “0.15m” to
“9.00m” in 0.15 meter steps.
(The default setting varies from country to country.)
This setting is set automatically by Audyssey MultEQ
®
Room Correction and Speaker Setup function (➔ 28).
This setting is NOT set automatically by
Audyssey MultEQ Room Correction and Speaker Setup
function (➔ 28).
This setting is set automatically by Audyssey MultEQ
Room Correction and Speaker Setup function (➔ 28).
… 46 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR808 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR808 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR808

Onkyo TX-NR808 User Manual - German - 196 pages

Onkyo TX-NR808 User Manual - Dutch - 196 pages

Onkyo TX-NR808 User Manual - French - 200 pages

Onkyo TX-NR808 User Manual - Italian - 196 pages

Onkyo TX-NR808 User Manual - Swedish - 196 pages

Onkyo TX-NR808 User Manual - Spanish - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info