492660

Onkyo TX-NR5010 Manual

66
Zoom out
Zoom in
Previous page
1/168
Next page
Advanced Operations
En-66
Main Menu Speaker Setup
Here you can check the settings made by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function, or set them manually, which is useful if
you change one of the connected speakers after using
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function.
Press RECEIVER and use SP on the remote controller to
select Speakers A or Speakers B. For details on SP, see
“Selecting Speaker Layout” (➔ page 55).
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
–the “Audio TV Out” setting is set to “On” (➔ page 84).
–“HDMI Control(RIHD)” is set to “On” (➔ page 83) and
you’re listening through your TV speakers.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“Speakers Type(Front A)” or “Speakers
Type(Front B)” setting. For details on speaker wire
connection, see “Bi-amping the Front Speakers”
(➔ page 18). When connecting speakers without
crossover network, you need to change the “Speakers
Type(Front A)” or “Speakers Type(Front B)” setting
beforehand. For details on connection, refer to “Using
Speakers Without Crossover Network” (➔ page 18).
Note
• When bi-amping is used, the AV receiver is able to drive up to 7.2
speakers in the main room.
• Before you change these settings, turn down the volume.
■ Speaker Impedance
` 4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
` 6ohms
:
Select if the impedances of all speakers are between 6
and 16 ohms.
■ Speakers Type(Front A)
` Normal
:
Select this if you’ve connected your front speakers A
normally.
` Bi-Amp:
Select this if you’ve bi-amped your front speakers A.
` Digital Crossover:
Select this if you’re using speakers without crossover
network.
■ Speakers Type(Front B)
` No
:
Select this if you’re not using speakers B.
` Normal:
Select this if you’ve connected your front speakers B
normally.
` Bi-Amp:
Select this if you’ve bi-amped your front speakers B.
` Digital Crossover:
Select this if you’re using speakers without crossover
network.
Tip
• If “Speakers Type(Front A)” or “Speakers Type(Front B)” is
set to “Digital Crossover”, a confirmation screen appears. Select
“Next (2-7. Digital Processing Crossover Network)” to display
the screen for Digital Processing Crossover Network
(➔ page 71). Continue with the settings.
■ Powered Zone 2, Powered Zone 3
` No
` Yes:
Zone 2/3 speakers can be used. (Powered Zone 2/3
enabled).
■ 11ch Playback
` No
` Yes
For 11.2-channel playback, set this setting to “Yes”. If you
select front wide speakers setting in Speaker Configuration
is set to “None”, it will be automatically switched to
“80Hz (THX)”.
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function (➔ page 42). For Speakers B,
you need to change the settings manually.
1 2 3 4 5
“Setup”
If you change these settings, you must run
Audyssey MultEQ XT32 Room Correction and
Speaker Setup again (➔ page 42).
To be continued
… 66 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR5010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR5010 in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR5010

Onkyo TX-NR5010 User Manual - German - 168 pages

Onkyo TX-NR5010 User Manual - Dutch - 168 pages

Onkyo TX-NR5010 User Manual - French - 168 pages

Onkyo TX-NR5010 User Manual - Italian - 168 pages

Onkyo TX-NR5010 User Manual - Swedish - 168 pages

Onkyo TX-NR5010 User Manual - Spanish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info