553762
76
Zoom out
Zoom in
Previous page
1/104
Next page
76
En
To use the same volume level as when the AV receiver was
last turned off, select “Last”.
The “Zone2 Power On Volume” and “Zone3 Power On
Vol ume ” cannot be set higher than the “Zone2 Maximum
Vol ume ” and “Zone3 Maximum Volume” setting.
This section explains how to turn Zone 2/3 on and off,
how to select an input source for Zone 2/3, and how to
adjust the volume for Zone 2/3.
Controlling Zone 2/3 from the AV receiver
Note
When Zone 2/3 is turned off, the output from the ZONE 2/3
12V TRIGGER OUT goes low (0 volts).
Controlling Zone 2/3 with the Remote
Controller
Note
To control Zone 2/3, you must press the remote controller’s
ZONE first.
ZONE turns red while Zone 2 is on, and green while Zone 3 is
on.
Note
Only analog input sources are output by the ZONE 2/3 PRE
OUT and FRONT WIDE/ZONE 2 L/R, FRONT HIGH/ZONE
3 L/R terminals. Digital input sources are not output. If no sound
is heard when an input source is selected, check if it’s connected
to an analog input.
You cannot select different AM or FM radio stations for your
main room and Zone 2/3. The same AM/FM radio station will be
heard in each room. For example, if you have an FM station for
the main room, that station will also be used in Zone 2.
When you connect ZONE3 speakers directly to the AV receiver,
Dolby Pro Logic IIz Height listening mode that require front
high speakers is unavailable.
When the input selector of Zone 2/3 is selected, power consump-
tion on standby mode slightly increases.
While Zone 2/3 is on, u functions will not work.
Using Zone 2/3
1
To turn on Zone 2/3 and select an input source,
press ZONE 2 or ZONE 3 followed by an input
selector button within 8 seconds.
Zone 2/3 turns on, the ZONE 2/3 indicator lights.
Tip
ZONE 2/3 12V TRIGGER OUT goes high (+12 V).
To select AM or FM, press TUNER input selector
and ZONE 2 or ZONE 3 repeatedly.
(North American models) You can also select SIR-
IUS.
To select the same source as that of the main room,
press ZONE 2 or ZONE 3 twice. “Zone 2 Selector:
Source” or “Zone 3 Selector: Source” appears on
the display.
2
To turn off Zone 2/3, press ZONE 2 or ZONE 3.
ZONE 2 or ZONE 3 indicator flashes.
Press OFF.
The zone is turned off, and the ZONE 2 or ZONE 3
indicator goes off.
ZONE 3
ZONE 2
OFF
ZONE 2 indicator
ZONE 3 indicator
Input selector buttons
1
Press ZONE repeatedly, then point the remote
controller at the AV receiver and press ON.
Tip
•The ZONE 2/3 12V TRIGGER OUT goes high (+12 V).
2
To select an input source for Zone 2/3, press
ZONE repeatedly, followed by INPUT SELEC-
TOR.
To select AM or FM, press TUNER input selector
and ZONE repeatedly.
(North American models) You can also select SIR-
IUS.
3
To turn off Zone 2/3, press ZONE repeatedly, fol-
lowed by STANDBY.
INPUT
SELECTOR
ON
ZONE
STANDBY
76


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1008 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1008

Onkyo TX-NR1008 User Manual - German - 204 pages

Onkyo TX-NR1008 User Manual - Dutch - 204 pages

Onkyo TX-NR1008 User Manual - French - 208 pages

Onkyo TX-NR1008 User Manual - Italian - 204 pages

Onkyo TX-NR1008 User Manual - Swedish - 204 pages

Onkyo TX-NR1008 User Manual - Spanish - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info