553762
75
Zoom out
Zoom in
Previous page
1/104
Next page
75
En
If you’ve connected your Zone 2/3 speakers to the AV
receiver, as explained in “Connecting Your Zone 2 Speak-
ers Directly to the AV receiver” ( 73) or “Connecting
Your Zone 3 Speakers Directly to the AV receiver”
( 74), you must set the “Powered Zone2” or “Powered
Zone3” setting to “Act” (Activated).
Note
Powered Zone 2 cannot be used if “Speakers Type(Front)” is
set to “Bi-Amp” ( 47).
This procedure can also be performed on the AV receiver by
using SETUP, arrows, and ENTER.
Note
This procedure can also be performed on the AV receiver by
using SETUP, arrows, and ENTER.
Zone2 Out, Zone3 Out
` Fixed
:
The Zone 2/3 volume must be set on the amp in that
zone.
` Variable:
The Zone 2/3 volume can be set on the AV receiver.
If you’ve connected your Zone 2/3 speakers to an amp
with no volume control, set the “Zone2 Out” and “Zone3
Out” setting, respectively, to “Variab le” so that you can
set the volume, balance, and tone of zone 2 and volume of
zone 3 on the AV receiver.
Zone2 Maximum Volume,
Zone3 Maximum Volume
` Off
, 50 to 99 (Absolute display)
` Off
, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume for
Zone 2/3.
Zone2 Power On Volume,
Zone3 Power On Volume
` Last
, Min, 1 to 99 or Max (Absolute display)
` Last
, QdB, –81dB to +18dB (Relative display)
This setting determines what the volume will be for
Zone 2/3 each time the AV receiver is turned on.
Setting the Powered Zone 2/3
1
Press RECEIVER followed by SETUP.
The main menu appears onscreen.
Tip
If the main menu doesn’t appear, make sure the appropri-
ate external input is selected on your TV.
2
Use q/w to select “Speaker Setup”, and then press
ENTER.
The “Speaker Setup” menu appears.
3
Use q/w to select “Speaker Settings”, and then
press ENTER.
The “Speaker Settings” menu appears.
4
Use q/w to select “Powered Zone2” or “Powered
Zone3”, and use e/r to select:
` Not Act
:
FRONT WIDE/ZONE 2 L/R or FRONT
HIGH/ZONE 3 L/R speaker terminals not
activated (Powered Zone 2/3 disabled).
` Act:
FRONT WIDE/ZONE 2 L/R or FRONT
HIGH/ZONE 3 L/R speaker terminals acti-
vated (Powered Zone 2/3 enabled).
5
Press SETUP.
The setup menu closes.
2. Speaker Setup
1. Speaker Settings
2. Speaker Configuration
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
2–1. Speaker Settings
Speaker Impedance
Speakers Type(Front)
Powered Zone2
Powered Zone3
6ohms
Normal
Not Act
Not Act
Setting the Multi Zone
1
Press RECEIVER followed by SETUP.
The main menu appears onscreen.
Tip
If the main menu doesn’t appear, make sure the appropri-
ate external input is selected on your TV.
2
Use q/w to select “Hardware Setup”, and then
press ENTER.
The “Hardware Setup” menu appears.
3
Use q/w to select “Multi Zone”, and then press
ENTER.
The “Multi Zone” menu appears.
4
Use q/w to select an item, and use e/r to change
it.
The items are explained below.
5
Press SETUP.
The setup menu closes.
7. Hardware Setup
1. Remote ID
2. Multi Zone
3. Tuner
4. HDMI
5. Auto Power Down
6. Network
7. Firmware Update
7-2. Multi Zone
Zone2 Out
Zone2 Maximum Volume
Zone2 Power On Volume
Zone3 Out
Zone3 Maximum Volume
Zone3 Power On Volume
Fixed
Off
Last
Fixed
Off
Last
75


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1008 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1008

Onkyo TX-NR1008 User Manual - German - 204 pages

Onkyo TX-NR1008 User Manual - Dutch - 204 pages

Onkyo TX-NR1008 User Manual - French - 208 pages

Onkyo TX-NR1008 User Manual - Italian - 204 pages

Onkyo TX-NR1008 User Manual - Swedish - 204 pages

Onkyo TX-NR1008 User Manual - Spanish - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info