553762

Onkyo TX-NR1008 Manual

47
Zoom out
Zoom in
Previous page
1/104
Next page
47
En
Main menu Speaker Setup
Here you can check the settings made by
Audyssey MultEQ Room Correction and Speaker Setup
function, or set them manually, which is useful if you
change one of the connected speakers after using
Audyssey MultEQ Room Correction and Speaker Setup
function.
Note
• These settings are disabled when:
– a pair of headphones is connected, or
–the “Audio TV Out” setting is set to “On” (➔ 58) and an
input selector other than HDMI is selected.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“Speakers Type(Front)” setting (➔ 47).
For hookup information, see “Bi-amping the Front Speak-
ers” (➔ 15).
Note
• When bi-amping is used, the AV receiver is able to drive up to
7.1 speakers in the main room.
• Before you change these settings, turn down the volume.
■ Speaker Impedance
` 4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
` 6ohms
:
Select if the impedances of all speakers are between
6 and 16 ohms.
■ Speakers Type(Front)
` Normal
:
Select this if you’ve connected your front speakers
normally.
` Bi-Amp:
Select this if you’ve bi-amped your front speakers.
Note
• Powered Zone 2 cannot be used if “Speakers Type(Front)” is
set to “Bi-Amp” (➔ 75).
■ Powered Zone 2, Powered Zone 3
See “Setting the Powered Zone 2/3” (➔ 75).
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your speak-
ers using Audyssey MultEQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to “80Hz(THX)” crossover.
■ Subwoofer
` Ye s
:
Select if a subwoofer is connected.
` No:
Select if no subwoofer is connected.
■ Front
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz,
200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■ Center
*1
, Surround
*1
, Surr Back
*2*3*4*5
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz,
200Hz
` None:
Select if no speaker is connected.
■ Front Wide
*1*2*6*7
, Front High
*1*2*8
` Full Band
` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
` None
:
Select if no speaker is connected.
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*3
If the “Surround” setting is set to anything other than “Full
Band”, “Full Band” cannot be selected here.
*4
If the “Speakers Type(Front)” setting is set to “Bi-Amp”
(➔ 47), this setting cannot be selected.
*5
If the Powered Zone 2 is being used (➔ 75), this setting can-
not be selected.
*6
If the “Powered Zone 2” setting is set to “Act” (➔ 75), this
setting cannot be selected.
*7
If the Powered Zone 3 is being used and
“Speakers Type(Front)” setting to “Bi-Amp” (➔ 47), this
setting cannot be selected.
*8
If the “Powered Zone 3” setting is set to “Act” (➔ 75), this
setting cannot be selected.
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ
®
Room Correction and Speaker
Setup function (➔ 29).
If you change these settings, you must run
Audyssey MultEQ Room Correction and Speaker
Setup again (➔ 29).
This setting is set automatically by Audyssey MultEQ
Room Correction and Speaker Setup function (➔ 29).
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1008 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1008

Onkyo TX-NR1008 User Manual - German - 204 pages

Onkyo TX-NR1008 User Manual - Dutch - 204 pages

Onkyo TX-NR1008 User Manual - French - 208 pages

Onkyo TX-NR1008 User Manual - Italian - 204 pages

Onkyo TX-NR1008 User Manual - Swedish - 204 pages

Onkyo TX-NR1008 User Manual - Spanish - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info