553762
30
Zoom out
Zoom in
Previous page
1/104
Next page
30
En
Note
When Audyssey MultEQ Room Correction and Speaker Setup is
complete, the “Equalizer” will be set to “Audyssey” ( 49).
The Audyssey indicator will light ( 9).
You can cancel Audyssey MultEQ Room Correction and
Speaker Setup at any point in this procedure simply by discon-
necting the setup microphone.
Do not connect or disconnect any speakers during
Audyssey MultEQ Room Correction and Speaker Setup.
If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ Room Correction and Speaker Setup
starts.
Changes to the room after Audyssey MultEQ Room Correction
and Speaker Setup requires you run Audyssey MultEQ Room
Correction and Speaker Setup again, as room EQ characteristics
may have changed.
Error Messages
While Audyssey MultEQ Room Correction and Speaker
Setup is in progress, one of the error messages below may
appear.
The options are:
` Retry:
Try again.
` Cancel:
Cancel Audyssey MultEQ Room Correction and
Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the source of
the noise and try again.
Speaker Matching Error!
The number of speakers detected was different from
that of the first measurement. Check the speaker con-
nection.
•Writing Error!
This message appears if saving fails. Try saving again.
If this message appears after 2 or 3 attempts, contact
your Onkyo dealer.
Speaker Detect Error
This message appears if a speaker is not detected. “No
means that no speaker was detected.
Tip
See “Speaker Configuration” for appropriate settings ( 13).
4
If you use a powered subwoofer(s), adjust the sub-
woofer volume level to 75dB.
Test tones are played through the subwoofer. Use the
volume control on the subwoofer.
Note
If your subwoofer does not have a volume control, disre-
gard the level displayed and press ENTER to proceed to
the next step.
If you set the subwoofer’s volume control to its maximum
and the displayed level is lower than 75 dB, leave the sub-
woofer’s volume control at its maximum and press
ENTER to proceed to the next step.
5
Press ENTER.
Audyssey MultEQ
®
Room Correction and Speaker
Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ Room Correction and Speaker
Setup runs. This process takes a few minutes. Please
refrain from talking during measurements and do
not stand between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ Room Correction and
Speaker Setup, unless you want to cancel the setup.
6
Place the setup microphone at the next position,
and then press ENTER.
Audyssey MultEQ performs more measurements.
This takes a few minutes.
7
When prompted, repeat step 6.
8
Use q/w to select an option, and then press
ENTER.
The options are:
` Save:
Save the calculated settings and exit
Audyssey MultEQ Room Correction and
Speaker Setup.
` Cancel:
Cancel Audyssey MultEQ Room Correction
and Speaker Setup.
Note
You can view the calculated settings for the speaker con-
figuration, speaker distances, and speaker levels by using
e/r.
9
Disconnect the speaker setup microphone.
TV
MultEQ: Auto Setup
Subwoofer Yes
Front 40Hz
Center 40Hz
Surround 100Hz
Front Wide None
Front High 100Hz
Surr Back 120Hz
Surr Back Ch 2ch
Save
Cancel
- - Review Speaker Configuration - -
Ambient noise is too high.
Retry
Cancel
MultEQ: Auto Setup
Error message
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1008 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1008

Onkyo TX-NR1008 User Manual - German - 204 pages

Onkyo TX-NR1008 User Manual - Dutch - 204 pages

Onkyo TX-NR1008 User Manual - French - 208 pages

Onkyo TX-NR1008 User Manual - Italian - 204 pages

Onkyo TX-NR1008 User Manual - Swedish - 204 pages

Onkyo TX-NR1008 User Manual - Spanish - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info