492647
37
Zoom out
Zoom in
Previous page
1/148
Next page
Turning On & Basic Operations
En-37
Error Messages
While Audyssey 2EQ
®
Room Correction and Speaker
Setup is in progress, one of the error messages below may
appear.
The options are:
` Retry:
Try again.
` Cancel:
Cancel Audyssey 2EQ Room Correction and Speaker
Setup.
Ambient noise is too high.
The background noise is too loud. Remove the source of
the noise and try again.
Speaker Matching Error!
The number of speakers detected was different from that
of the first measurement. Check the speaker connection.
Writing Error!
This message appears if saving fails. Try saving again. If
this message appears after 2 or 3 attempts, contact your
Onkyo dealer.
Speaker Detect Error
This message appears if a speaker is not detected. “No
means that no speaker was detected.
Tip
See “Speaker Configuration” for appropriate settings
( page 12).
Changing the Speaker Setup Manually
You can manually make changes to the settings found
during Audyssey 2EQ Room Correction and Speaker
Setup.
See also:
“Speaker Configuration” ( page 55)
“Speaker Distance” ( page 56)
“Level Calibration” ( page 56)
“Equalizer Settings” ( page 57)
Note
Please note that THX recommends any THX main speakers be set
to “80Hz(THX)”. If you set up your speakers using
Audyssey 2EQ Room Correction and Speaker Setup, please
make sure manually that any THX speakers are set to
80Hz(THX)” crossover ( page 55).
Sometimes due to the electrical complexities of subwoofers and
the interaction with the room, THX recommends setting the level
and the distance of the subwoofer manually.
Sometimes due to interaction with the room, you may notice
irregular results when setting the level and/or distance of the main
speakers. If this happens, THX recommends setting them
manually.
Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by Audyssey 2EQ Room Correction and Speaker
Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the subwoofer’s
volume to the half-way point, set it to its highest crossover
frequency, and then try running Audyssey 2EQ Room
Correction and Speaker Setup again. Note that if the
volume is set too high and the sound distorts, detection
issues may occur, so use an appropriate volume level. If the
subwoofer has a low-pass filter switch, set it to Off or
Direct. Refer to your subwoofer’s instruction manual for
details.
Retry
Cancel
Ambient noise is too high.
AUDYSSEY
2EQ: Auto Setup
Error message
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR 717 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR 717 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR 717

Onkyo TX-NR 717 User Manual - German - 144 pages

Onkyo TX-NR 717 User Manual - Dutch - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info