492647
36
Zoom out
Zoom in
Previous page
1/148
Next page
Turning On & Basic Operations
En-36
Note
You can cancel Audyssey 2EQ Room Correction and Speaker
Setup at any point in this procedure simply by disconnecting the
setup microphone.
Do not connect or disconnect any speakers during Audyssey 2EQ
Room Correction and Speaker Setup.
If the AV receiver is muted, it will be unmuted automatically
when Audyssey 2EQ Room Correction and Speaker Setup starts.
Changes to the room after Audyssey 2EQ Room Correction and
Speaker Setup requires you run Audyssey 2EQ Room Correction
and Speaker Setup again, as room EQ characteristics may have
changed.
1
Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV receiver
is connected.
2
Set the speaker setup microphone at the Main
Listening Position a, and connect it to the SETUP
MIC jack.
The speaker setting menu appears.
Note
The on-screen menus appear only on a TV that is connected
to HDMI OUT MAIN. If your TV is connected to other
video outputs, use the AV receiver’s display when changing
settings.
3
When you’ve finished making the settings, press
ENTER.
Perform the “Speaker Setup” according to your
speaker configuration:
Speakers Type(Front) ( page 55)
Powered Zone 2 ( page 55)
Powered Zone 3 ( page 55)
4
Use q/w to select “Audyssey Quick Start” or
“Audyssey 2EQ Full Calibration”, and then press
ENTER.
Speaker setup microphone
SETUP MIC jack
2EQ: Auto Setup
AUDYSSEY
Speakers Type(Front)
Powered Zone 2
Powered Zone 3
Normal
No
No
5
Press ENTER.
Audyssey 2EQ
®
Room Correction and Speaker Setup
starts.
Test tones are played through each speaker as
Audyssey 2EQ Room Correction and Speaker Setup
runs. This process takes a few minutes. Please refrain
from talking during measurements and do not stand
between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey 2EQ Room Correction and Speaker
Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to
step 8.
6
Place the speaker setup microphone at the next
position, and then press ENTER.
Audyssey 2EQ performs more measurements. This
takes a few minutes.
7
When prompted, repeat step 6.
8
Use q/w to select an option, and then press ENTER.
The options are:
` Save:
Save the calculated settings and exit
Audyssey 2EQ Room Correction and Speaker
Setup.
` Cancel:
Cancel Audyssey 2EQ Room Correction and
Speaker Setup.
Save
Cancel
-- Review Speaker Configuration --
Subwoofer
Front
Center
Surround
Front Wide
Front High
Surround Back
Surround Back Ch
Yes
100Hz
40Hz
100Hz
None
None
120Hz
2ch
2EQ: Auto Setup
AUDYSSEY
Tip
You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using e/r.
9
Use q/w to select a target, and use e/r to change
the setting.
After the results of Audyssey 2EQ have been saved,
the menu will display the “Audyssey” ( page 60),
“Dynamic EQ” ( page 60), “Dynamic Volume”
( page 61) settings.
Note
When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
These settings are applied to all input selectors.
10
Press ENTER.
11
Disconnect the speaker setup microphone.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR 717 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR 717 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR 717

Onkyo TX-NR 717 User Manual - German - 144 pages

Onkyo TX-NR 717 User Manual - Dutch - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info