553753
30
Zoom out
Zoom in
Previous page
1/64
Next page
30
Enjoying music or videos with the TX-DS696
Switching the display
While listening to or watching an input source, you can display the
information regarding the type of source and signal being input by
pressing the DISPLAY button on the TX-DS696 or the remote
controller.
When an input source other than FM or AM is selected:
* If the input signal does not have a program format, then this will
be skipped.
Input + volume
Program format*
Input +
Listening mode
or Multi Ch
When FM or AM is selected as the input source:
FM/AM frequency +
Preset no.
FM/AM +
Listening mode
ch
Using the sleep time (remote controller only)
The SLEEP button enables you to set the TX-DS696 to turn off
automatically after a specified time period. If you press it once, the
TX-DS696 will turn off after 90 minutes. Each time it is pressed
thereafter, the remaining time until the TX-DS696 turns off
decreases by 10 minutes. While, the sleep function is enabled, you
can press the SLEEP button to see how much time is left. To cancel
the sleep function, press the SLEEP button when the time displayed
is less than 10 minutes.
If you are using the remote zone (Zone 2), it will turn off at the same
time as the main zone. If you want to set the sleep function for Zone
2 only, set the sleep function with main zone turned on and then put
the main zone into the standby state.
Temporarily changing the speaker output levels
To change the individual speaker volumes temporarily, follow the
procedure given below. Each channel can be set between 12 to +12
decibels. Note that the calibration settings will return to the original
settings when the TX-DS696 is put in standby.
1. Press the CH LEVEL button and
select the desired speaker.
2. Turn the jog dial to adjust the
volume level.
DISPLAY
CH LEVEL
PUSH TO ENTER
DSP
/
MODE ADJ
When using the remote controller:
1. Press the RCVR MODE button.
2. Press the CH SEL button and select
the desired speaker.
3. Press the LEVEL or button to
adjust the volume level.
TX-DS696 Remote controller
MUTING
HOME THEATER CONTROLLER
RC
-
440M
STANDBY/ON
STANDBY
OFF
ON
POWER
MASTER VOLUME
BASS
TREBLE
AV
RECEIVER
TX
-
DS696
PHONES
FM AM PHONO C
DTAPEDVD
REC OUT
ZONE
2 ZONE 2 LEVEL
CH LEVEL
VIDEO 3 VIDEO 4VIDEO 2VIDEO 1
VCR 2VCR 1
AUDIO
SELECTOR
TUNING PRESET
SMART
SCAN
NAVIGATOR
PRESET MEMORY
FM
MODEDISPLAY DIMMER
PUSH TO ENTER
DSP
/
MODE ADJ
SETUP
RETURN
CH LEVELDISPLAY DIMMER
SLEEP
LEVEL
DIMMER
CH SEL
DISPLAY
Jog dial
Adjusting the brightness of the front display
You can adjust the brightness of the front display of the TX-DS696
with DIMMER button on the remote controller or on the TX-DS696
front panel with other than European models.
DIMMER
TX-DS696
(Other than European models)
Remote controller
Remote controller
Notes:
You cannot select a speaker if the Speaker Config sub-menu of
the Speaker Setup is set to No or None.
If the speaker level is set to +1 dB or higher, the maximum level
indicated on the display will change if you raise the volume
level.
When you press the TEST button after you set the level, the
current level will be used as the value set via the test tone.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-DS696 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-DS696 in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-DS696

Onkyo TX-DS696 User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info