462128
32
Zoom out
Zoom in
Previous page
1/40
Next page
En-32
Connecting Components Not Reached by the
Remote Controller Signals (IR IN/OUT)
In order to use the remote controller to control the
receiver from a remote location, you will need to
prepare a multiroom kit (sold separately) such as one
listed below:
Multiroom A/V distribution and control system such
as those from Niles
®
and Xantech
®
* Xantech is a registered trademark of Xantech
Corporation.
* Niles is a registered trademark of Niles Audio
Corporation.
Effective Sensor Layout
Example for the main room
If the receiver is located inside a cabinet or other
enclosure where the infrared rays from the remote
controller cannot enter, then operation with the remote
controller will not be possible. In such a case, it will be
necessary to install a remote sensor at a location outside
of the cabinet so that the infrared rays from the controller
can be sensed.
Example for Zone 2
The IR IN input allows you to control the receiver from
Zone 2 with the remote controller even though Zone 2
may be on the other side of the building from the main
zone. The diagram below shows how to make the proper
connections for Zone 2.
Making Sensor Connections
When you place the IR receiver in the main room, connect
the cable from the connecting block to the IR IN terminal.
Make the connection as shown below. Do not plug any
equipment into the power outlet until all the connections
are complete.
Effective Sensor Layout
In this situation, you will need to use a commercially
available IR emitter. Connect the mini plug of the IR
emitter to the IR OUT terminal on the receiver and then
place the IR emitter on the remote sensor of the
component or facing it. When the IR emitter is
connected, only the signal input to the IR IN terminal is
output to the IR OUT terminal. The signal input from the
remote sensor on the front of the receiver will not be
output to the IR OUT terminal.
Making Sensor Connections
The IR emitter should be connected to the receiver’s IR
OUT Terminal, as shown below.
If Remote Controller Signal Does Not
Reach the Receiver Remote Sensor
IR IN
IR Receiver
Remote controller
Connecting
block
Receiver
In the
cabinet
Signal flow
Remote controller
Receiver
IR Receiver
Connecting
block
Main room Zone 2
To IR IN
Signal flow
If Remote Controller Signal Does Not
Reach Other Components
from
connecting block
Mini plug cable
Receiver
Signal flow
Remote controller
IR Receiver
Connecting
block
Receiver
IR IN
IR OUT
Other
component
IR Emitter
Emitter
Receiver
Remote control
sensor
Signal flow
Other
component
Mini plug
Mini plug
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-8030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-8030 in the language / languages: English as an attachment in your email.

The manual is 5,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-8030

Onkyo TX-8030 User Manual - German - 80 pages

Onkyo TX-8030 User Manual - Dutch - 80 pages

Onkyo TX-8030 User Manual - French - 80 pages

Onkyo TX-8030 User Manual - Italian - 80 pages

Onkyo TX-8030 User Manual - Swedish - 80 pages

Onkyo TX-8030 User Manual - Spanish - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info