452195
105
Zoom out
Zoom in
Previous page
1/108
Next page
105
En
Troubleshooting
Case1:
If “No Update” is displayed on the front display of the AV
controller, the firmware has already been updated. You do
not need to do anything further.
Case2:
If an error occurs, “Error!! *-** No media” is displayed
on the front display of the AV controller. (Alpha-numeric
characters on the front display are denoted by asterisks.)
See the following table and take appropriate action.
Errors during update via network
Case3:
If you do not have a wired connection to the network,
please contact Onkyo Support ( 106).
Case4:
If an error occurs during updating process, disconnect then
reconnect the power cord and try again.
Case5:
If an error has occurred due to wrong selection of input
sources, turn off and on the AV controller. Then retry the
update.
The AV controller allows you to update firmware using a
USB storage device.
*
In this procedure, on-screen display may vary depending on the
model.
Note
Make sure your AV controller and TV are turned on.
Never unplug or turn off the AV controller during updating pro-
cess.
Never plug or unplug an HDMI cable and a USB device during
updating process.
Never unplug the USB mass storage device and the power cord
during updating process.
Do not access the AV controller from PC during updating pro-
cess.
It will take about 60 minutes to update the firmware.
The AV controller will retain all your settings after update is fin-
ished.
Before you start
•CheckHDMI Control(RIHD)” setting ( 61). The
update may not be successful if this setting is on.
Turn off the controller device connected via RS232C and
via Ethernet network.
Turn off Zone 2 and Zone 3.
Stop playback of content from Internet radio, iPod, USB
or servers, etc.
How to turn off RIHD
Update procedure
Error Code Description
*
-10,
*
-20
Ethernet cable is not detected. Connect the
cable properly.
*
-11,
*
-13,
*
-21,
*
-28
Internet connection error.
Check the following items:
Make sure IP address, subnet mask, gateway
address, and DNS server are configured prop-
erly.
Make sure the router is turned on.
Make sure the AV controller and the router
are connected with Ethernet cable.
Make sure the setup configuration of the
router is set properly. See the instruction
manual of the router.
If your network allows only one client con-
nection and there is any other device already
connected, the AV controller cannot access
the network. Consult your Internet Service
Provider (ISP).
If your modem does not function as a router,
you will need a router. Depending on your
network, you may need to configure the
proxy server if needed. See the document
provided by your ISP. If you still cannot
access the Internet, DNS or proxy server may
be temporarily down. Contact your ISP.
Others Retry the update procedure from the begin-
ning. If the error persists, please contact
Onkyo Support ( 106) and provide the error
code.
Updating the Firmware via USB
1
In the Main menu select “Hardware Setup”.
2
Select “HDMI”.
3
Set “HDMI Control(RIHD)” to “Off”.
1
Connect a USB storage device to your PC. If
there is any data in the USB storage device,
remove it.
2
Download the firmware file from the Onkyo
web site. The file name is as follows:
ONKAVR0001_*******.zip
Unzip the downloaded file. The following three
files are created:
ONKAVR0001_*******.of1
ONKAVR0001_*******.of2
ONKAVR0001_*******.of3
3
Copy the extracted files to the USB storage
device. Be careful not to copy the zip file.
4
Remove the USB storage device from your PC
and connect it to the USB port on the AV con-
troller.
When the AV controller has two USB ports, you
can use either one.
105


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo PR-SC5508 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo PR-SC5508 in the language / languages: English as an attachment in your email.

The manual is 4,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo PR-SC5508

Onkyo PR-SC5508 User Manual - German, French - 216 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info