452195
104
Zoom out
Zoom in
Previous page
1/108
Next page
104
En
Firmware Update
There are the following methods to update the firmware:
via network and via USB storage. Please choose either one
that suits your condition. Before you start, carefully read
the update procedure. It will take about 60 minutes to
update the firmware.
Update via network
You need a wired Internet connection to update the
firmware.
Update via USB storage ( 105)
Please prepare a USB storage device such as a USB
flash memory stick. You need at least 32 MB of avail-
able space to update the firmware.
Note
The storage media in the USB card reader may not work.
If the storage device has been partitioned, each section will be
treated as an independent device.
If the USB mass storage device contains a lot of data, the AV
controller may take a while to read it.
Operation with all USB mass storage devices including the abil-
ity to power them is not guaranteed.
Onkyo accepts no responsibility whatsoever for the loss or dam-
age to data stored on a USB mass storage device when that
device is used with the AV controller. We recommend that you
back up your important music files beforehand.
If you connect a USB hard disk drive to the USB port, we rec-
ommend that you use its AC adapter to power it.
USB hubs and USB devices with hub functions are not sup-
ported. Do not connect your USB mass storage device via a USB
hub.
USB memory devices with security functions are not supported.
In no event shall Onkyo be liable to you or any third party for any
damages, whatsoever, arising from your use of or inability to use
the firmware, including but not limited to, loss of any equipment,
media or data, or other special, incidental or consequential dam-
ages, even if Onkyo has been advised of the possibility of such
damages.
The AV controller allows you to update firmware using net-
work connection on rear panel.
*
In this procedure, on-screen display may vary depending on the
model.
Note
Make sure your AV controller and TV are turned on and Ethernet
cable is connected to rear panel of the AV controller.
Never unplug or turn off the AV controller during updating pro-
cess.
Never plug or unplug an HDMI cable and Ethernet cable during
updating process.
Never unplug the power cord during updating process.
Do not access the AV controller from PC during updating pro-
cess.
It will take about 60 minutes to update the firmware.
The AV controller will retain all your settings after update is fin-
ished.
Before you start
Check “HDMI Control(RIHD)” setting ( 61). The
update may not be successful if this setting is on.
Turn off the controller device connected via RS232C and
via Ethernet network.
• Turn off Zone 2 and Zone 3.
Stop playback of content from Internet radio, iPod, USB
or servers, etc.
How to turn off RIHD
Update procedure
See the Onkyo web site for latest information.
Updating the Firmware via Network
1
In the Main menu select “Hardware Setup”.
2
Select “HDMI”.
3
Set “HDMI Control(RIHD)” to “Off”.
1
Press RECEIVER followed by SETUP on the
remote controller.
Main menu will be displayed on TV screen. Proce-
dures thereafter can also be performed on the AV
controller by using its SETUP, arrow, and ENTER
buttons.
2
Go to “Hardware Setup” menu.
3
Go to “Firmware Update” menu.
Note that the Firmware Update option will be grayed
out about 50 seconds after the AV controller is
turned on. Please wait.
4
Select “via NET” and press ENTER.
5
Select “Update” and press ENTER.
Updating will begin.
As the updating progresses, the TV screen may dis-
appear depending on the program updated. In this
case, you can see the update progress on the front
display of the AV controller. The TV screen will
reappear when you finish the update and turn on the
AV controller.
6
Message “Complete!” appears on the front dis-
play of the AV controller, indicating that the
update has been completed.
7
Using ON/STANDBY on the front panel, turn off
and on the AV controller.
Do not use ON or STANDBY on the remote control-
ler.
Congratulations!! Now you have the latest firmware
on your Onkyo AV controller.
104


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo PR-SC5508 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo PR-SC5508 in the language / languages: English as an attachment in your email.

The manual is 4,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo PR-SC5508

Onkyo PR-SC5508 User Manual - German, French - 216 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info