136557
41
Zoom out
Zoom in
Previous page
1/96
Next page
41
Connecting
—Continued
Connect the IR receiver to the DV-SP1000/
DV-SP1000E as shown below.
Controlling Other Out-of-range
Components
For another component that is out of range of its remote
controller, you can use a commercially available IR
emitter to retransmit the remote controller signals
received at the DV-SP1000/DV-SP1000E’s IR IN, as
shown below.
Connect the IR emitter to the DV-SP1000/
DV-SP1000E’s IR OUT, and place the IR emitter in front
of the other AV component’s remote control sensor (usu-
ally located on its front panel), as shown below. See the
instructions supplied with the IR emitter.
Only remote controller signals received by the
DV-SP1000/DV-SP1000E’s IR IN are fed through to the
IR OUT. Signals picked up by the DV-SP1000/
DV-SP1000E’s remote control sensor are not.
Notes:
Before connecting the power cord, complete all of the
necessary audio and video connections.
Do not use a power cord other than the one supplied
with the DV-SP1000/DV-SP1000E, which is designed
exclusively for use with the DV-SP1000/
DV-SP1000E and should not be used with any other
component.
•Never disconnect the power cord from the
DV-SP1000/DV-SP1000E while the other end is still
plugged into a wall outlet. Doing so may cause an
electric shock. Always disconnect the power cord
from the wall outlet first.
The DV-SP1000/DV-SP1000E (not the Canadian
model) is shipped with the POWER switch in the ON
position ( ). When the power cord is connected for
the very first time, the DV-SP1000/DV-SP1000E will
go on standby and the STANDBY indicator will light
up.
•To completely shutdown the DV-SP1000/
DV-SP1000E, set the POWER switch to the OFF posi-
tion ( ). (This does not apply to the Canadian model).
OUT
IN
IR
DV-SP1000/DV-SP1000E
from connecting block
Miniplug cable
Signal flow
IR IN
IR OUT
Connecting
block
IR receiver
DV-SP1000/
DV-SP1000E
IR emitter
Remote controller
Other
component
Signal flow
OUT
IN
IR
Signal flow
DV-SP1000/
DV-SP1000E
Remote control
Other component
sensor
from connecting block
Miniplug cable
Miniplug
IR emitter
IR Emitter
Connecting the Power Cord
1
Plug the supplied power cord into the
DV-SP1000/DV-SP1000E’s AC INLET.
2
Plug the other end of the power cord into
a suitable AC wall outlet.
The STANDBY indicator lights up.
The STANDBY indicator comes on only if the
POWER switch is in the ON ( ) position. (This
does not apply to the Canadian model).
M
ODEL NO.
DPC
-
7.4
DVD
CHANGER
AC
INLET
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo dv sp 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo dv sp 1000 in the language / languages: English as an attachment in your email.

The manual is 4,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo dv sp 1000

Onkyo dv sp 1000 User Manual - French, Spanish - 192 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info