371088

Onkyo dr s 2 2 Manual

82
Zoom out
Zoom in
Previous page
1/88
Next page
82
Notes:
• The remote controller codes for Onkyo CD player, MD player,
cassette tape deck or HD Recorder have already been
programmed into buttons on the remote controller. You may,
however, use these buttons to program the codes for other
remote controllers. If you wish to restore the Onkyo preset codes
after you program new codes, you must first erase the new codes
(see page 83).
• The remote controller has 300 memory slots (6 modes × 50
buttons). Some remote controllers may have more commands
that can be remembered by the remote controller. In such cases,
it will be necessary for you to determine which commands are
more important than others.
• If no button is pressed for more than 30 seconds during the
programming, or if you perform an invalid operation during
programming, the SEND/LEARN indicator flashes three times
quickly, and the remote controller exits the programming mode.
Resume from Step 2.
• If a failure occurs during programming, the SEND/LEARN
indicator flashes three times quickly, and the remote controller
exits the programming mode. Resume from Step 3.
• If a failure occurs five times in row during programming, the
remote controller exits the programming mode. Resume from
Step 3.
• If you try to program beyond the learning capacity of the remote
controller, the SEND/LEARN indicator flashes six times quickly,
and the remote controller exits the programming mode. Try
programming under a different MODE button.
• When you want to program a command to a button to which you
have already programmed a command, simply follow the same
procedure given and programming for that button will be
overwritten.
• The remote controller uses infrared rays to send its commands,
as do most other remote controllers. Though most remote
controller codes can be memorized by the remote controller, be
aware that some remote controllers use a system that is quite
different from the remote controller and therefore may not be able
to be programmed.
• Some remote controllers have a single button that performs
multiple functions (for example, the function may change each
time the button is pressed). If this is the case, each function must
be programmed to a separate button on the remote controller.
• Once you have transferred the commands from the other remote
controller, refer to the instruction manual that came with that
product for instructions on how to operate that product.
• Make sure both the remote controller and the other remote
controller have new batteries. If either of them has batteries that
are low, you may not be able to program the commands of the
other remote controller properly into the remote controller.
See page 83 for how to erase the memorized commands from
all buttons.
Controlling other components connected to the DVD Receiver
Press and hold down the button
(that corresponds to the command
you are programming) on the
remote controller of the other
device until the SEND/LEARN
indicator on the remote controller
flashes twice.
After flashing twice, the SEND/LEARN
indicator will light again.
Repeat Steps 3 and 4 to transfer all
the commands you desire from the
other remote controller and
program them to buttons on the
remote controller under the same
MODE.
Repeat Steps 2 through 4 to program
commands to a different MODE (e.g., when
programming from a different remote
controller).
Press the MODE button that you
pressed in step 2 to complete the
programming.
Operate the newly programmed
buttons to make sure the learning
function was performed properly.
6
5
4
7
… 82 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo dr s 2 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo dr s 2 2 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info