Manual Onkyo dr 90 (page 59 of 68) (English)

370695

Zoom out

Zoom in

1/68

Additional Operation

Recording the Picture and Sound From

Different Sources at the Same Time

The picture from the VIDEO 2 source continues to be output

through the VIDEO OUT jacks even if you change to another

audio source (TAPE/MD, FM, or AM) or TV.

Therefore if you select VIDEO 2 first, then select TAPE/MD,

FM, AM, or TV, you can record the picture from the VIDEO 2

source and the sound from the TAPE/MD, FM, AM, or TV at

the same time, using the recording equipment connected to

the VIDEO 1 jacks.

Digital recording from the source

connected to the digital input connectors

to the digital recording equipment

connected to the digital output connector

The digital input connectors are as follows:

• The DIGITAL INPUT OPTICAL VIDEO 1 connector, and

• The DIGITAL INPUT COAXIAL VIDEO 2 connector.

The digital output connector is the DIGITAL OUTPUT

OPTICAL connector.

Recording digital sound signals from sources connected to the

digital input connectors using digital recording equipment

connected to the digital output is possible unless:

• The recording is against SCMS (Serial Copy Management

System) rules (for details of SCMS rules, refer to the

manual of the digital recording equipment),

• The digital sound signals are copy protected,

• The digital signals are in bitstream format (the recordable

digital signal format is PCM –– two channel digital stereo

sound signals), or

• The sampling frequency is out of the recordable range of

the recording equipment (for recordable sampling

frequency, refer to the manual of the digital recording

equipment). Note that the maximum signal frequency output

from the DVD Receiver is 48 kHz.

Analog recording from a DVD Video

played using the DVD Receiver

The digital sound signals are converted to analog signals and

output to the analog output jacks unless the DVD video is

recorded in the DTS Surround system.

Although the speakers can reproduce DTS Surround sounds,

DTS signals are not converted to analog signals. Therefore,

no analog signals are output for recording. See e in the

tables on page 41.

Tips to obtain better analog signals (only when the

reproduced sound signals are in the PCM format)

The digital signals will be converted through the D/A (Digital-to

Analog) converter. When the digital signals are being

converted using higher frequency (kHz) and higher

quantization (bit), better analog signals will be obtained.

To convert PCM signals using the higher frequency and higher

quantization, set the sound signal conversion method to “96k

Sound.” See page 40 and f in the table on page 41.

DVD

Note

Although better analog signals can be obtained with the “96k Sound”

conversion method reproduced PCM signals may not be output from

the digital output connector (DIGITAL OUTPUT OPTICAL) depending

on frequency and quantization. See also “Note” in “Digital recording

from a DVD video played by the DVD Receiver” below.

Digital recording from a DVD video

played by the DVD Receiver

The digital sound signals are output to the DIGITAL OUTPUT

OPTICAL connector in the most suitable format when the

sound signal conversion method is set to “Bitstream” (see

page 40). However, if the conversion method is set to

“Bitstream” or “96k Sound” when DOLBY DIGITAL Surround

sound is reproduced, the signals will be output in the

bitstream format from the DIGITAL OUTPUT OPTICAL

connector as in b in the table on page 41. The bitstream

signals are unrecordable.

Therefore, to record DOLBY DIGITAL Surround sounds you

need to change the conversion method to “PCM.” Once the

conversion method is changed to “PCM,” the DOLBY DIGITAL

sound signals are converted into the recordable frequency

and quantization (48 kHz/16 bit) as in c in the same table

mentioned above.

DTS Surround sound is unrecordable from both the digital

output connector and analog output jacks regardless of the

sound signal conversion methods.

Notes

• If the conversion method is set to “PCM,” the DTS Surround sounds

of a DVD video will not be reproduced from the speakers nor output

to the DIGITAL OUTPUT OPTICAL connector. See g in the tables

on page 41.

• If the sound signal conversion method is set to “96k Sound” to

reproduce the high-frequency/high-quantization sound signals in their

original sound quality (see page 40) or to obtain better analog signals

(see on the left), the DIGITAL OUTPUT OPTICAL connector will

output no signals depending on the frequency and quantization as in

d in the tables on page 41.

To record high frequency PCM sound signals, the conversion

method must be set to “Bitstream” or “PCM,” so that the frequency/

quantization are converted to the 48 kHz/16 bit format which is

recordable.

Analog and Digital recording from a

VIDEO CD played using the DVD Receiver

VIDEO CDs are recorded in the MPEG1 format. MPEG1 format

will be output in the recordable form of 44.1 kHz/16 bit through

the DIGITAL OUTPUT OPTICAL connector, and converted to

analog signals in the 44.1 kHz/16 bit format, regardless of the

conversion method. For details, see the table on page 41.

Analog and Digital recording from an

audio CD played using the DVD Receiver

PCM sound signals are output to the DIGITAL OUTPUT

OPTICAL connector, and converted to analog signals and

output to the analog output jacks regardless of the conversion

method.

DTS Surround sound is unrecordable. Because DTS Surround

sound signals of an audio CD are output to the DIGITAL

OUTPUT OPTICAL connector in the bitstream format and no

signal will be output to the analog output jacks regardless of

the conversion method. For details, see the table on page 41.

VCD

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo dr 90 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Onkyo dr 90 Manual

Product: