370695
40
Zoom out
Zoom in
Previous page
1/68
Next page
40
To Listen to a High-Frequency/High-
Quantization Format Source in its
Original Sound Quality – 96k Sound
The high frequency/high quantization sound signals below are
converted into 48 kHz/16 bit sound signals and sent to the
speakers when the “Audio Out Select” (sound signal
conversion method) is set to the standard setting, “Bitstream.
High frequency/high quantization signals
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
To listen to the high-frequency (kHz)/hight-quantization (bit)
format sounds in their original sound quality, follow the steps
below.
Change the sound signal
conversion method to “96k Sound”
following the steps on the left.
As you see a in the table titled “Sound
from the speakers” on the opposite page,
the DVD videos recorded in 48 kHz/24 bit,
96 kHz/16 bit, 96 kHz/20 bit, and 96 kHz/
24 bit are reproduced through the
speakers at the same kHz and bit rate
respectively.
If a subwoofer is connected, set the
subwoofer configuration to “NO”
following steps 1 and 2 in “Speaker
Setup” on page 18.
Skip the rest of the steps by pressing
ENTER repeatedly.
Press SURROUND MODE on the
remote controller or DVD Receiver
repeatedly until “STEREO” appears
in the DVD Receiver's display.
See “Using Onkyo’s original sound effects
– DSP selection” on page 31.
DVD
1
2
3
1
AUDIO
See previous
page.
2
ENTER
CLEAR
To turn off the audio setting display
Press CLEAR.
Notes
The “Audio Out Select” setting in the setting menu (see page 50) is
for automatic selection of the sound conversion method when the
disc is inserted. Therefore, the selection in this section will not
change the setting of “Audio Out Select” in the setting menu.
When you turn on the DVD Receiver or replace a disc, the DVD
Receiver returns to the automatic setting in the setting menu (See
page 44.)
The reproduced disc sound will be output in the most suitable format automatically through the
connected speakers and output connector/jacks on the DVD Receiver when “Audio Out Select”
in the setting menu is set to “Bitstream” (see page 50).
However, you may need to convert the sound format in different ways depending on your
purpose and preference.
For example, when you wish to:
Listen to the high-frequency (kHz)/high-quantization (bit) format source in its original sound
quality (see below), or
Record the DVD video sound reproduced in the DOLBY DIGITAL format using recording
equipment such as an MD recorder connected to the DIGITAL OUTPUT OPTICAL connector
on the DVD Receiver (see next page).
This function enables you to temporarily change the sound signal conversion method which has been
selected automatically according to the automatic setting in the setting menu (see pages 44 and 50).
Changing the Sound Signal
Conversion Method
CLEAR
SENDING/
LEARNED
DVD RECEIVER
TV
LEVEL SETUP
TITLE
SURROUND
MODE
DVD TV
ENTER
RETURN
AUDIO
SEARCH
ANGLE ZOOM
CLEAR
TUNER
SETUP
VIDEO 1
TAPE
VIDEO 2
INPUT SELECTOR
OPEN/
CLOSE
DIMMER
SLEEP
DISPLAY
ON
STANDBY
POWER
SUBTITLE
CH SEL
LEVEL
TEST
TONE
231
564
89
7
0
+10
MUTING
RANDOM
REPEAT A-B MEMORY
VOLUME
PRESET
PAUSE FF
PLAYDOWN
STOP SLOW
UP
FR
CHANNEL
TV/
VCR
POWER
REMOTE CONTROLLER RC-399M
TUNER
MENU
1
2
Audio:
Audio OUT Select : Bitstream
ENG PCM 2CH
1
Audio:
Audio OUT Select : 96k Sound
ENG PCM 2CH
1
Changing the Sound Signal
Conversion Method Temporarily
Press AUDIO during playback.
The current audio setting is displayed for
about 3 seconds.
Press / while the audio setting is
displayed on the TV screen.
Each time you press / , the setting
changes as follows:
Bitstream 96k Sound PCM
↑↑
For details about “Bitstream, “96k Sound,
and “PCM, see the explanation on page
50 and table on the opposite page.
DVD
VCD
CD
The current sound signal
conversion method
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo dr 90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo dr 90 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info