581067
14
Zoom out
Zoom in
Previous page
1/16
Next page
En-14
Troubleshooting
To return to the default setting
When this unit is not operating properly, it may return to
normal condition by returning the condition to default
setting in following procedure.
While the unit is on, press and hold the DIRECT button
and press the Í ON/STANDBY button.
All the LEDs will go off and the unit will turn into standby
mode after approximately 5 seconds later, and the
condition will return to default setting.
The unit does not turn on.
0 Confirm that the power plug is securely plugged in to
an outlet.
0 Unplug the power cord once, wait 5 seconds and then
plug it in again.
The unit turns off unexpectedly.
0 Confirm that the Auto Standby is not enabled. The
Auto Standby may operate when the input signal is
very small. In such case, set the Auto Standby to Off
(> 12).
0 When the protection circuit is activated (because of
speaker short-circuit, overload, or over-current), the
unit enters standby mode. Remove the source of the
problem and turn the unit back on.
There’s no sound.
0 Make sure the correct input source is selected.
0 Check if the volume is minimized or muting is
operating.
0 Check all connections and correct as necessary.
0 While headphones are connected, the speakers output
no sound.
0 There may be a loose contact when no sound is output
from headphone, so check the connection.
0 (North America and Continental European models)
The unit does not support digital formats other than
PCM. Inputting a digital format other than PCM may
cause loud noise.
There is noise.
The sound quality is not good.
0 Make sure the speaker cables are connected with the
correct polarity.
0 Make sure all audio connecting plugs are pushed in all
the way.
0 Place the unit as far away as possible from TVs and
other devices that emit strong electromagnetic waves.
0 If you have any devices that emit high-intensity radio
waves near the unit, such as a cellular phone that’s
being used to make a call, the unit may output noise.
0 Bundling audio cables with speaker cables or power
cords may degrade the sound quality, so refrain from
doing it.
0 Audio performance will be at its best about 10 to 30
minutes after the unit has been turned on and had time
to warm up.
The RI functions don’t work properly.
0 Check that each device is connected correctly.
0 (North American and Continental European models)
Check that the RI MODE switch is set correctly.
0 The connecting method may vary depending on the
device that will be connected. See the instruction
manual for the connected device.
Onkyo is not responsible for damages (such as CD rental
fees) due to unsuccessful recordings caused by the unit’s
malfunction. Before you record important data, make sure
that the material will be recorded correctly.
The unit contains a microcomputer for signal processing
and control functions. In very rare situations, severe
interference, noise from an external source, or static
electricity may cause it to lockup. In the unlikely event
that this should happen, unplug the power cord, wait at
least 5 seconds, and then plug it again.
If the top of this unit is too hot to touch even when no
sound is played back, it is necessary to reconsider the
installation location. Secure appropriate ventilation so it
will not obstruct heat dissipation.
Before starting the procedure
Problems may be solved by simply turning the power
on/off or disconnecting/connecting the power cord,
which is easier than working on the connection,
setting and operating procedure. Try the simple
measures on both the unit and the connected device.
A-9010_eng.book 14 ページ 2014年12月25日 木曜日 午前10時48分
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo A-9010B-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo A-9010B-S in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo A-9010B-S

Onkyo A-9010B-S User Manual - German, Dutch - 64 pages

Onkyo A-9010B-S User Manual - French - 32 pages

Onkyo A-9010B-S User Manual - Italian, Swedish - 64 pages

Onkyo A-9010B-S User Manual - Spanish - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info