492763
21
Zoom out
Zoom in
Previous page
1/22
Next page
TROUBLESHOOTING (cont.)
Problem: Solution
The Home Producer
8 does not operate
your home
entertainment
component?
The
Home
Producer 8
is not
performing
commands properly?
You make a mistake
when setting up your
Home Producer 8
?
display screen will change to
[SEL TO RS]. Press
SELECT. The display
screen will then return to
[TV and the TIME].
Try all of the codes listed for
your brand of home
entertainment component
in the “Set-Up Codes”
section. If this does not
work, try searching for your
code. Make sure the home
entertainment component
you are setting up is able
to be operated with an
infrared remote control.
Try all of the codes listed for
your brand of home
entertainment component
in the “Set-Up Codes”
section. Many set-up codes
may allow some degree
of operation. However, only
one set-up code will work
correctly with your home
entertainment component.
During any set up procedure,
except for Macros and Timed
Sequences, the ESC key will
return you to the
[DEVICE and the TIME]
screen without saving. If you
make a mistake when setting
up a Timed Sequence, return
to the Timed Sequence
menu and delete the
incorrect sequence. If you
make a mistake when saving
a macro, erase the incorrect
macro by re-saving a new
macro on the same key.
TROUBLESHOOTING
Problem: Solution
LCD screen begins
to fade, does not
appear or the red
light blinks five times
when you press a
key?
[MEM FAULT]
appears on the LCD
screen.
Replace the batteries with
four (4) new AAA alkaline
batteries. Immediately
before removing the
batteries, please refer to
page 8 and re-enter your
TV’s setup code. This will
allow the
Home Producer 8
to retain its memory upon
removing the batteries. If
you do not, upon entering
your fresh batteries, the LCD
screen may say
[MEM FAULT].
If [MEM FAULT] does
appear on the LCD screen,
press and hold MAGIC
until the display screen
changes from [TV and the
TIME] to [TIMED SEQ].
Press the MENU - key one
time. The display screen will
change to [CODE SET UP].
Press SELECT. The display
will change to
[DEV SET UP]. Press
SELECT and the display
screen will change to [TV].
Enter code 9-6-1. Press
SELECT, then ESC. Now
press and hold MAGIC until
the display screen changes
from [TV and the TIME] to
[TIMED SEQ]. Press the
MENU + key one time. The
display screen will change to
[CONFIGURE]. Press
SELECT. The display
screen will change to
[THEATR SEL]. Press
MENU + once. The display
screen will change to
[SERVICE]. Press SELECT.
The display screen will
change to [MFG RESET].
Press SELECT. The
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for One for All URC 8090 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of One for All URC 8090 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info