492763
20
Zoom out
Zoom in
Previous page
1/22
Next page
COMPLIANCE WITH THE FCC RULES AND
REGULATIONS
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and radiates radio frequency
energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try and correct the interference
by one or more of the following measures:
* Reorient or relocate the receiver antenna
* Increase the separation between the equipment
and the receiver
* Connect the equipment into an outlet that is different from
that to which the receiver is connected
* Consult the dealer or an experienced radio/television
technician for help
The user is cautioned that changes and modifications made to the
equipment without the approval of the manufacturer could void
the user’s authority to operate his equipment.
FCC Authorization Label
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
FCC ID #:
Home Producer 8:
MG3N868629
Command Center: MG3-15-1925R
The Command Center also includes an additional IR
signal extension cord for use with a component that
is not in direct line-of-sight of the Command Center.
If you have a component that is not in the line-of-
sight of the Command Center:
1 Plug the 4 ft. IR signal extension cord into
the back of the Command Center.
2 Run the IR signal extension cord to the
component that is not in the line-of-sight of
the Command Center.
3 Using the supplied double-sided tape, attach
the IR signal extension cord so that the LED
is over or next to the IR sensor of your home
theater component.
4 Test the
Home Producer 8.
The Command
Center will convert the RF signal from the
Home Producer 8
into and IR signal and
transmit that signal to your component
through the IR signal extension cord.
NOTE: If the IR signal extension cord does not
control the component that is not in the line-of-sight
of the Command Center, reposition the LED until the
component is able to be controlled, then re-attach
the LED.
LED
SPECIFICATIONS
Remote Power ..................................................... 4 AAA Batteries
RF Command Console Power ................................. 120 Volts AC
Remote to RF Command Console Range .... 100 Feet (30.48m)
RF Command Console to Device Range .... 25 Feet (7.62m) ±30˚
Remote Dimensions (HWD)........................ 9 3/8 x 2 7/8 x 1 3/8
RF Command Console
Dimensions (HWD) ............................ 1 9/16 x 5 1//16 x 4 inches
Remote Weight (without Batteries) ............................ 8 oz. (220g)
RF Command Console Weight ............................... 10.4 oz (300g)
Specifications are typical: individual units might vary.
Specifications are subject to change and improvement without
notice.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for One for All URC 8090 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of One for All URC 8090 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info