Manual Olsberg Merapi (page 14 of 40) (English, German, Dutch, French, Spanish)

812276

Zoom out

Zoom in

1/40

Operation

Permissible fuels

The following fuels are approved:

●Natural shopped wood in the form of billet wood

Maximum length: ..............33 cm

Circumference: ....approx. 30 cm

Billet wood reaches a moisture content of 10 to 15%

after being stored outdoors for 2 to 3 years (only cov-

ered at the top) and is then ideally suited for heating.

Freshly cut wood has a very high moisture content

and so burns badly. Apart from the very low calorif-

ic value it is also harmful for the environment. The in-

creased condensate and tar formation can lead to re-

place and chimney sooting.

This diagram shows that the consumption rate with

freshly-felled wood (caloric value 2.3 kWh/kg) is al-

most twice as high as the consumption rate with dry

wood (caloric value 4.3 kWh/kg).

Moisture [%]

dry wood that has been stored for at least 2 years

Caloric value [kWh/kg]

freshly-felled wood

You will only achieve optimum combustion and heat

in an environmentally friendly way with these fuels.

Adding the fuel in small quantities avoids unnecessary

emissions. Clean burning can be identied by the fact

that the rebrick becomes a light colour.

According to the German Federal Immission Control

Act, it is forbidden e.g. to burn the following fuels in

stoves:

●Moist wood or wood treated with wood

preservatives

●Sawdust, chippings, grinding dust

●Bark and chipboard waste

●Slack coal

●Other wastes

●Paper and cardboard (except for igniting)

●Straw

Please note before heating for the rst time

Locking hook in OPEN position

●When opening the combustion chamber door, the

locking hook automatically retracts and is held by

a spring in the OPEN position. If the locking hook

is unintentionally activated when the combustion

chamber door is open, it must be manually returned

to the OPEN position before the combustion cham-

ber door can be closed.

●Remove all accessories from the ash pan and com-

bustion chamber.

●The odour given off by the evaporation of the pro-

tective coating disappears after the stove has been

burning for several hours (ventilate the room well).

●The stove has a high quality temperature resistant

coat, which does not achieve its nal strength un-

til the stove has been heated for the rst time. You

should therefore never leave anything on the stove

and not touch the surfaces as the paint coat could

otherwise be damaged.

●As soon as the kindling material has burned down,

put on 2 burnouts consisting of 3 kg wood ensuring

that the temperature resistant coating reaches its -

nal rmness.

●Attention: The storage of fuel below the combus-

tion chamber door, before the lower front

shield (Fig.3, Pos.8) is prohibited.

Igniting

● Before ignition, check that no ammable objects are

placed on the stove.

●Empty the ash pan if necessary and slide back in.

●Open the combustion air slide valve complete.

●Grate in open position = operating lever pulled out

●Place the ignition material (ignition cubes and dry,

smaller ignition wood) and ignite it.

●Close the door to the combustion chamber so that

the kindling material can catch re.

●As soon as the igniting material is burning, add a

quantity of fuel corresponding with the required heat

(see chapter “heating”).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Olsberg Merapi in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Olsberg Merapi Manual

Product: