Manual Olsberg Corvus (page 11 of 36) (English, German, Dutch, French, Spanish)

812271

Zoom out

Zoom in

1/36

Installing the stove

The oor on which the stove is installed must be even

and horizontal. The stove may only be installed on an

adequate load-bearing oor. The stove can be stood

on a metal oor sheet or glass sheet to protect the

ooring.

If the ooring or carpet is inammable, a stable and

non-combustible spark protection plate must be used.

This must extend 50 cm to the front and 30 cm to each

side beyond the edge of the combustion chamber

opening. Under the stove no spark protection plate is

required.

Assembly sequence

●The Ø 150 stovepipe connection can be installed at

the top or rear. The stove is supplied ready for con-

nection from above. If you wish to connect it at the

rear, the following steps must be carried out to make

the necessary modications:

- Break out the cover in the back panel.

- Replace the connector sleeve and the sealing

cover.

●Decide where the stove is to be installed. There

must be no objects made of combustible materials

within a distance of 80 cm of the stove’s radiation

area, measured from the combustion chamber’s in-

spection glass, nor may any be placed within this

area subsequently.

Depending on the installation position of the stove in

front of walls that need to be protected (ammable

or load-bearing), the following distances from walls

need to be observed in accordance with the position

of the combustion chamber door to the wall / side

panel or the back panel (see schematic diagram).

When not dealing with walls that need to be protect-

ed, you merely need to observe a minimum distance

of approx. 5 cm to allow for proper heat dissipation.

●Install the pipe lining (provided on site) in the chim-

ney. The connection height can be individually spec-

ied for a top stovepipe connection, however should

not exceed 1.5 m from the connector sleeve. For the

rear stovepipe connection heights please refer the

“Technical Data“ chapter. No combustible material is

permitted within a radius of 20 cm around the stove

pipe.

●Connect the stovepipe at both connection points

with stove putty so that the stove pipe is permanent-

ly sealed.

●Push the stove onto its planned position and orient it

so that the stovepipe ts into the pipe lining.

The stovepipe connections must be tight. The

stovepipe must not protrude into the chimney.

Bear in mind that on partition walls in accordance

with test specication EN 13240 the temperature

of 85°C can be reached, and with light wallpaper

or similar combustible construction materials this

can result in colour changes.

20 cm

40 cm 40 cm

80 cm

Stove installed straight in corner

20 cm

80 cm

Stove installed diagonally in corner

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Olsberg Corvus in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1.69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Olsberg Corvus Manual

Product: