Manual Olsberg Corvus (page 10 of 36) (English, German, Dutch, French, Spanish)

812271

Zoom out

Zoom in

1/36

Technical Data

●Nominal thermal output ................................. 6,0 kW

●Room heat output .......................................... 6,0 kW

●Height to middle of the connector pipe

with the connection at the back ................... 985 mm

●Height to the top edge of connector pipe

with the connection at the top .....................1151 mm

●Connection pipe ...................................... Ø 150 mm

●max. Weight................................................... 235 kg

●Height to middle

of combustion air connection ....................... 230 mm

●Connection combustion air ...................... Ø 125 mm

●Operating mode ........................ Intermitting burning

Regulations to be observed

●Local and building law regulations

●The stove must be installed by a professional and

connected to the chimney. The specic national reg-

ulations for safe installation of the connector must be

complied with. The connecting piece used must pos-

sess an opening for cleaning.

●The stove must be regularly checked by a

professional.

The heating stove’s re door is self-closing; it is there-

fore approved for connection to chimneys with multiple

connections.

Chimney design

The chimney design is according to DIN EN 13384-1

and -2 or to the specic national regulations. The chim-

ney must comply with the temperature class T400.

Necessary data

Closed operation

with billet wood / wood briquettes / lignite briquettes:

●Nominal thermal output ................. 6,0 / 6,0 / 6,0 kW

● Waste air mass ow rate ............... 4,3 / 3,9 / 4,0 g/s

●Waste air temperature at

connection duct ........................... 309 / 305 / 282 °C

●Minimum delivery pressure at

nominal thermal output ...................... 12 / 12 / 12 Pa

Combustion air supply

It must be guaranteed that there is enough combustion

air available for the stove. For the proper function of the

stove, a necessary combustion air volume current of

18,7 m³/h must be considered.

External combustion air connection

By an external operating mode, the combustion air

can be added from outside through a leak-proof line or

through a supply duct in the chimney. Thus, speak with

your district chimney sweep master.

Due to energy saving reasons, the combustion air in-

let should be able to be blocked if the stove is not being

operated. This can occur through a shut-off valve in the

combustion air line or through the air slide valves on

the stove. If a shut-off valve is used, this must be clear-

ly identied with CLOSED/OPEN.

Through the shutoff, it is avoided that heat is removed

from the set-up room through the constant circulation

of cold combustion air and cold combustion air lines

may lead to an increased formation of condensation.

Attention:

The combustion air line may not be closed during

operation!

In order to feed the combustion air to the stove exter-

nally via a pipe instead of from the room in which it is

installed, it is possible to screw a Ø 125 mm combus-

tion air pipe to the back of the stove. If the combus-

tion air pipe installed is longer than 3 m, calculations

will have to be carried out to verify an adequate sup-

ply of combustion air. At extremely low outdoor temper-

atures, condensation can occur on the combustion air

duct. For this reason it must be insulated with a suitable

insulating material. Observe the rules of the oven and

air heating construction craft.

Use the Olsberg combustion air pipes with sealing lip.

Attention:

Appliances with external combustion air connec-

tion are not suitable for concurrent operation with

ventilation systems, without a supplemental safe-

ty system.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Olsberg Corvus in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1.69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Olsberg Corvus Manual

Product: