16706
29
Zoom out
Zoom in
Previous page
1/64
Next page
5
TO SEND A DOCUMENT WITH THE RECEIVER RAISED
1. Insert the document in the ADF or the manual document
feeder.
The display shows on the top line:
DOCUMENT READY
and on the bottom line, the default contrast value: "NOR-
MAL".
The initial resolution value is: "
" (standard).
If you want, change the contrast and resolution values as
described previously.
2. Lift the receiver to engage the line.
The display shows:
OFF HOOK
and the length of the transmission in minutes and seconds in
the top right-hand corner.
3. To dial the number of the correspondent to whom you wish
to send the document, press the keys:
-
Your correspondent’s number may be made up of max. 64
digits.
If your correspondent’s fax machine is set up for auto-
matic reception, you will hear the fax machine signal.
If it is set up for manual reception, the correspondent
himself will answer so you can ask him to press the start
key on his fax machine, after which you will hear the fax
machine signal.
4. To start sending, press the key:
The message "CONNECTING" appears on the display.
If the document is sent correctly, once this operation has
been completed, the display will show the message "TX
COMPLETED" for a few seconds.
AUTOMATIC REDIAL
If no connection is established due to line errors or because the
correspondent's number is busy, the fax machine automatically
redials the number up to three times.
TO SEND A DOCUMENT TO SEVERAL CORRESPONDENTS
The fax machine's memory allows you to send a document (even
at a preset time: "Delayed transmission") to several correspond-
ents (max. 10): "Broadcast transmission". See "To send a docu-
ment from the memory".
TO SEND A DOCUMENT FROM THE MEMORY
1. Insert the document in the ADF or the manual document
feeder.
The display shows on the top line:
DOCUMENT READY
and on the bottom line, the default contrast value: "NOR-
MAL".
The initial resolution value is: "
" (standard).
If you want, change the contrast and resolution values as
described previously.
2. Press the key
until the display shows:
TX FROM MEMORY
3. Press the key:
The fax machine starts to save the document. Once saved,
the display shows the message "DOC.N. XXXX" and then:
TYPE TIME
HH:MM
4. To type the time at which you wish to send the document, for
example "16:50", press the keys:
-
5. To confirm both the current time and the time set in step 4,
press the key:
The display shows:
TYPE FAX NUMBER
NUM/TOUCH/SPEED
6. Dial your correspondent's number in any of the available
methods: directly on the numeric keypad or using the one-
touch keys or speed dialling codes (see "To set one-touch
and speed dialling").
To do this, press the keys:
-
7. Press the key:
The fax machine prompts you to enter another number:
TYPE FAX NUMBER
NUM/TOUCH/SPEED
If you want to send the document to more than one corre-
spondent, repeat the previous two steps once for each
correspondent.
If you want to send the document to one correspondent
only, move straight on to the next step without typing any
numbers.
8. To complete the procedure, press the key:
Once the procedure has been completed, the display shows:
AUTOMATIC 00
MEMORY TX
note
If there is a power failure, the transmission from the memory
will be cancelled.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olivetti LAB_S120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olivetti LAB_S120 in the language / languages: English as an attachment in your email.

The manual is 3,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Olivetti LAB_S120

Olivetti LAB_S120 User Manual - German - 64 pages

Olivetti LAB_S120 User Manual - Dutch - 64 pages

Olivetti LAB_S120 User Manual - Danish - 64 pages

Olivetti LAB_S120 User Manual - French - 64 pages

Olivetti LAB_S120 User Manual - Italian - 64 pages

Olivetti LAB_S120 User Manual - Portuguese - 64 pages

Olivetti LAB_S120 User Manual - Swedish - 64 pages

Olivetti LAB_S120 User Manual - Spanish - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info