452059
29
Zoom out
Zoom in
Previous page
1/81
Next page
21
ENGLISH
4. Press the [Clear] key to program another feature otherwise exit the
program mode by turning the PRG key to the OFF position.
Example: Program a standard 3% add-on rate.
Type/Press:
[0300] + [0] + [+%/PO] + [Clear]
Fraction Rounding
Fraction rounding is used to round figures with decimals up or down
to the nearest whole numbers and is used for percent tax, percent
discount and percent add-on calculations. Choose from the following
three options to select the rounding as needed:
Rounding Code Fraction Rounding
00 a fraction of a pence is rounded down one pence
50 a fraction under one half pence is rounded
down one pence, a fraction above one half pence
is rounded up one pence
99 a fraction of a pence is rounded up one pence
Setting the Rounding Code
Proceed as follows to program fraction rounding:
1. Turn the PRG key to the PRG position.
2. Type the [rounding code] and press the [Charge] key. The
programmed rounding code is automatically printed along with the
caption "CHARGE".
3. Press the [Clear] key to program another feature, otherwise exit the
program mode by turning the PRG to the OFF position.
Example: Program the rounding code so that a fraction under one half
pence is rounded down one pence, a fraction above one half pence
is rounded up one pence up.
Type/Press:
[50] + [Charge] + [Clear]
Decimal Point Position
The decimal point setting is preset to the x.xx format. This format
can be changed, as needed, to one of the other settings below.
Changing the Decimal Point Position
Proceed as follows to define a new position for the decimal point.
1. Turn the PRG key to the PRG position.
2. Type the status number [0, 1, 2 or 3] to select the desired format as
indicated in the following table:
Status Number Format
0x
1 x.x
2 x.xx
3 x.xxx
3. Press the [-%/RA] key to set the new format. The setting made is
automatically printed along with the caption "R-A-".
4. Press the [Clear] key to program another feature, otherwise exit the
program mode by turning the PRG to the OFF position.
Example: Program the cash register so that two digits are left after the
decimal point.
Type/Press:
[2] + [-%/RA] + [Clear]
29


Need help? Post your question in this forum.

Forumrules
1

Forum

olivetti-ecr-2450t

Reset search

  • How do I delete a over ring of £700 on a Olivetti register till?
    Submitted on 23-4-2022 at 18:01

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olivetti ECR 2450T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olivetti ECR 2450T in the language / languages: English as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info