452059

Olivetti ECR 2450T Manual

16
Zoom out
Zoom in
Previous page
1/81
Next page
8
ENGLISH
These symbols clear automatically when you start the next entry or
press the [Clear] key.
Positioning the Customer Display
To position the customer display, simply raise it out of its slot and
then rotate it to the desired position.
Error Conditions
The Error Alarm
The error alarm warns of an operator error (usually when a wrong key
is pressed for a specific type of entry) or of an error made during cash
register programming. The error alarm can also indicate that the
Control Lock is in the wrong position for the current operation. In case
of error, the error tone sounds, the letter E is displayed on the customer
display, the message ERROR is displayed on the operator display and
the keypad locks.
Clearing an Error
Press the [Clear] key to clear an error. The tone ends, the displays
clear and the keypad unlocks, allowing you to continue with the
transaction or restart the program.
If an error condition cannot be cleared, perform a general clearance.
Bear in mind, however, that one of the two general clearance
procedures, explained in the next section, will set all counters and
totals to zero and will cancel all programmed functions.
NOTE: The [Clear] key also clears an incorrect entry from the display
prior to pressing a registration key. Once an entry is printed,
the [Void] key must be used to correct an error.
General Clearance
If the cash register does not function, for example while programming
and the error signal cannot be stopped by pressing the [Clear] key,
perform a general clearance. There are two ways of performing a
general clearance, whereby the second method resets all totals and
counters and cancels the programming. Use this method only as
last resort.
General Clearance without Clearing Totals and the
Programming
1. Turn the Control Key to the OFF position.
2. Make sure four charged AA batteries are inserted in the battery
compartment.
3. Unplug the cash register from the power socket.
4. Wait ten seconds and then reconnect the cash register to the power
socket and resume your operation.
If the cash register remains in an error condition, proceed with the
second general clearance method.
General Clearance with the Clearing of Totals and all
Cash Register Programming
NOTE: Be careful that this procedure erases all totals and counters,
and cancels the programming of the cash register.
1. Turn the control key to the OFF position.
2. Open the printer compartment cover and remove the back-up
batteries.
3. Unplug the cash register from the power socket.
4. Wait for 15 minutes and then plug the cash register back to the
electrical power outlet.
5. Insert the batteries once again.
6. Reprogram the cash register.
… 16 …


Need help? Post your question in this forum.

Forumrules
1

Forum

olivetti-ecr-2450t

Reset search

  • How do I delete a over ring of £700 on a Olivetti register till?
    Submitted on 23-4-2022 at 18:01

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olivetti ECR 2450T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olivetti ECR 2450T in the language / languages: English as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info