688885
57
Zoom out
Zoom in
Previous page
1/144
Next page
E
GR
57
P
NL
Equipos con bomba de calor
(g. 16)
Fije la junta en el codo de drenaje
e inserte el empalme de drenaje en
el oricio de la taza presente en la
base; gire 90° para ensamblarlos
correctamente. Si hay una pérdida
de agua de la unidad exterior
durante el funcionamiento en modo
de calefacción, conecte el empalme
de drenaje a una alargadera del tubo
de drenaje (adquirida localmente).
A - junta
B - junta de drenaje
C - oricio de la taza presente en la
base de la unidad exterior
Montaje de la unidad externa
Después de haber localizado la
posición ideal para la ubicación
de la unidad (como descrito en los
cap. 2.4.1 y 2.4.2) proceder como
se indica:
- Posicionar la unidad en el
basamento de apoyo, si fuera
necesario, sobre pies de goma
antivibración (g. 17).
1 entrada de aire
2 salida de aire
- Atornillar, sin apretar
completamente, las eventuales
tuercas de sujeción.
- Vericar el nivel de la unidad con
un nivel de aire, y, en caso de ser
necesario nivelar por medio de
espesore.
- Atornillar definitivamente las
eventuales tuercas de sujeción.
* modelos 9 - 10 - 12 K
** modelos 18 K
*** modelos 24 K
ÓõóêåõÝò ìå áíôëßá
èåñìüôçôáò (åéê. 16)
Óôåñåþóôå ôç öëÜíôæá óôç ãùíßá
áðïóôñÜããéóçò, óôç óõíÝ÷åéá
ôïðïèåôÞóôå ôï óýíäåóìï
áðïóôñÜããéóçò óôçí ïðÞ ôïõ
ðéÜôïõ ôçò âÜóçò, óôñÝøôå êáôÜ
90° ãéá íá ôá óõíáñìïëïãÞóåôå
óùóôÜ. ÓõíäÝóôå ôï óýíäåóìï
áðïóôñÜããéóçò ìå ìßá ðñïÝêôáóç
óùëÞíá áðïóôñÜããéóçò (èá
ôçí áãïñÜóåôå óôïí ôüðï
ôïðïèÝôçóçò), óå ðåñßðôùóç
ðïõ õðÜñ÷åé äéáññïÞ íåñïý áðü
ôçí åîùôåñéêÞ ìïíÜäá êáôÜ
ôç äéÜñêåéá ôçò ëåéôïõñãßáò
èÝñìáíóçò.
A - öëÜíôæá
B - óýíäåóìïò áðïóôñÜããéóçò
C - ïðÞ ôïõ ðéÜôïõ ôçò âÜóçò ôçò
åîùôåñéêÞò ìïíÜäáò
ÓôåñÝùóç åîùôåñéêÞò
ìïíÜäáò
Áöïý åíôïðßóåôå ðñþôá ôçí
éäáíéêÞ èÝóç ãéá ôçí ôïðïèÝôçóç
ôçò ìïíÜäáò (üðùò ðåñéãñÜöåôáé
óôá êåö. 2.4.1 êáé 2.4.2) ðñïâáßíåôå
üðùò õðïäåéêíýåôáé:
- ÔïðïèåôÞóôå ôç ìïíÜäá óôï
ðëáßóéï âÜóçò óôçñéæüìåíç, åÜí
÷ñåéÜæåôáé, óå áíôéêñáäáóìéêÜ
ëÜóôé÷á (åéê. 17).
1 åßóïäïò áÝñá
2 Ýîïäïò áÝñá
- Âéäþóôå, ÷ùñßò íá óößîåôå
åíôåëþò, ôá åíäå÷üìåíá
ðáîéìÜäéá óôåñÝùóçò.
- ÅëÝãîôå ôç óôÜèìç ôçò ìïíÜäáò
ìå Ýíá áëöÜäé ìå öõóáëßäá êé
åÜí ÷ñåéáóôåß âÜëôå ôáêÜêéá.
- Âéäþóôå êáëÜ ôá åíäå÷üìåíá
ðáîéìÜäéá óôåñÝùóçò.
* ìïíôÝëá 9 - 10 - 12 K
** ìïíôÝëá 18 K
*** ìïíôÝëá 24 K
2
Aparelhos com bomba de
calor (g. 16)
Fixar a junta no cotovelo de
drenagem, depois introduzir a junta
de drenagem no furo do prato da
base, rodar de 90° para as montar
correctamente. Ligar a junta de
drenagem com uma extensão de
tubo de drenagem (adquirida no
comércio), no caso em que haja
uma saída de água pela unidade
externa durante o funcionamento
em modalidade aquecimento.
A - junta
B - junta de drenagem
C - furo do prato da base da
unidade externa
Montagem da unidade externa
Após ter individuado a posição ideal
para o posicionamento da unidade
(como descrito nos cap. 2.4.4 e
2.4.2) proceder do seguinte modo:
- Posicionar a unidade sobre a base
de apoio, e se necessário, sobre
as borrachinhas anti-vibrantes
(g. 17).
1 entrada de ar
2 saída de ar
- Enroscar, sem apertar
completamente, as eventuais
porcas de xação.
- Verificar o nível da unidade
com uma bolha de nível,
e se necessário, utilizar uma
espessura.
- Apertar definitivamente as
eventuais porcas de xação.
* modelos 9 - 10 - 12 K
** modelos 18 K
*** modelos 24 K
2.4.4
Apparaten met warmtepomp
(afb. 16)
Bevestig de pakking in de elleboog
van de drainageleiding en plaats de
drainagekoppeling vervolgens in het
gat van de basisplaat. 90° draaien
om de onderdelen op correcte
wijze te kunnen monteren. Sluit
de drainagekoppeling aan op een
verlenging van de drainageleiding
(ter plekke aangeschaft) voor
het geval waarin er water uit
de buitenunit stroomt tijdens de
werkwijze verwarming.
A - pakking
B - drainagekoppeling
C - gat van basisplaat buitenunit
Montage buitenunit
Nadat de ideale positie voor de
plaatsing van de unit gevonden is
(zoals beschreven in de par. 2.4.1
en 2.4.2) dient men als volgt te
handelen:
- Breng de unit in positie op de
basis, zo nodig op de rubber
elementen tegen het trillen (afb.
17).
1 luchtinlaat
2 luchtuitlaat
- Draai de eventuele
bevestigingsmoeren vast zonder
deze volledig te spannen.
- Controleer de nivellering van de
unit met een waterpas en breng
zonodig verdikkingen aan.
- Schroef de eventuele
bevestigingsmoeren definitief
vast.
* 9 - 10 - 12 K modellen
** 18 K modellen
*** 24 K modellen
17
487*
514**
540***
298*
340**
350***
1
1
2
2.4.3
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olimpia Splendid NEXYA S4 INVERTER 24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olimpia Splendid NEXYA S4 INVERTER 24 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info