688885
44
Zoom out
Zoom in
Previous page
1/144
Next page
GB
F
D
44
I
Etrier (g. 6)
A - sortie unité interne
B - plaque d’installation
C - orice tube réfrigérant gauche ø
65
D - orice tube réfrigérant droite ø
65
Exécution du trou pour le
passage des tuyaux
Si les conduites de branchement
arrivent derrière l’unité intérieure côté
droit, il est nécessaire d’effectuer le
trou dans le mur pour le passage des
tuyaux.
- Faire le trou au centre de la position
avec un foret de 8-10 mm et une
inclinaison vers l’extérieur de 5%
(pour faciliter l’écoulement du liquide
de condensation). Procéder ensuite
au perçage dénitif avec un foret pour
carottage guidé de 65 mm.
- Introduire dans le trou le tuyau de
drainage et ceux du frigorigène
ainsi que le câblage pour le
branchement électrique.
Si les conduites de branchement
arrivent derrière l’unité intérieure
côté gauche, il est nécessaire
d’effectuer dans le mur, en
correspondance aux tuyaux de
l’installation réfrigérante un trou de
ø 65 (g. 6).
Haltebügel (Abb. 6)
A - Ausgang Inneneinheit
B - Installationsplatte
C - Bohrung Kühlschlauch links ø
65
D - Bohrung Kühlschlauch rechts
ø 65
Bohrung für das Durchführen
der Rohre
Werden die Verbindungsleitungen zur
rechten Rückseite der Inneneinheit
geführt, ist in der Wand eine Bohrung
für das Durchführen der Rohre
einzuarbeiten.
- In der Mitte der Stelle, an der die Einheit
montiert wird, mit einer Bohrerspitze
(8-10 mm) eine Bohrung mit einer
Neigung von 5% (zur ungehinderten
Ableitung des Kondenswassers)
durchführen. Danach das vorgebohrte
Loch mit einer geführten Breitkopf-
Bohrerspitze (65mm) aufbohren.
- Die Ableitung für das Kondenswasser
und das Kühlmittel sowie die Kabel
für den elektrischen Anschluss in die
Bohrung einführen.
Werden die Verbindungsleitungen
zur linken Rückseite der Inneneinheit
geführt, ist in der Wand, und zwar auf
der Höhe der Kühlrohre, eine Bohrung
(ø 65 mm) einzuarbeiten (Abb. 6).
6
2
Staffa (g. 6)
A - uscita unità interna
B - piastra di installazione
C - foro tubo refrigerante sinistro ø 65
D - foro tubo refrigerante destro ø 65
Esecuzione foro passaggio
tubi
Nel caso in cui le linee di
collegamento arrivino dalla parte
posteriore destra dell’unità interna
si rende necessario eseguire nella
parete il foro per il passaggio dei
tubi.
- Eseguire nel centro della
posizione il foro con una punta di
8-10 mm e un’inclinazione verso
l’esterno del 5% (per consentire
un’agevole deuire del liquido di
condensa). Procedere poi alla
foratura denitiva con una punta
a tazza guidata di 65 mm.
- Inserire nel foro la linea di
drenaggio e quelle del refrigerante
e il cablaggio per il collegamento
elettrico.
Nel caso in cui le linee di collegamento
arrivino dalla parte posteriore
sinistra dell’unità interna si rende
necessario eseguire nella parete, in
corrispondenza dei tubi dell’impianto
refrigerante un foro di ø 65 (g. 6).
2.3.2
2.3.3
Brace (g. 6)
A - indoor unit outline
B - installation plate
C - left rear side refrigerant pipe
hole ø 65
D - right rear side refrigerant pipe
hole ø 65
Drilling pipe passage holes
If the service lines for connection
come from the right rear side of the
inside unit it will be necessary to
drill a hole in the wall for passage
of the pipes.
- Drill the hole at the centre of the
site of installation using an 8-10
mm bit and tilting it downward
towards the outside by 5% (to
facilitate the ow of condensation).
Finish the hole with a 65 mm
auger.
- Insert the drain line and the
cooling fluid line in the hole,
as well as the cable for electric
connection.
If the service lines for connection
come from the left rear side of the
inside unit it will be necessary to drill
a hole ø 65 in the wall for the cooling
pipes (g. 6).
L
R
H
ø ø
R mm L mm H mm ø mm
115,6 101,6 47 65
123,6 183,6 47 65
9 -10
12
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olimpia Splendid NEXYA S4 INVERTER 24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olimpia Splendid NEXYA S4 INVERTER 24 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info