47387
9
Zoom out
Zoom in
Previous page
1/25
Next page
8
COMMAND CENTER
3-2 Start > Status Pages
These pages allow you to verify the various settings (printing, network and e-mail) that
were made on the operation panel or using COMMAND CENTER.
3-3 Start > Information Page
These pages allow you to verify the Contact Information settings, the model number of
this machine, and version of COMMAND CENTER.
Page Description
Start > Status pages:
Network: General
This allows you to verify the settings made under SNMP, TCP/IP,
AppleTalk, and NetBEUI in the Advanced Page.
For more information on SNMP, refer to Advanced > Management /
E-mail: SNMP on page 21. For more information on other items, refer to
Advanced > Protocols: TCP/IP: General on page 15.
Start > Status pages:
Network: IP Filters
This displays the IP address range for each protocol that was set and that
have access permissions as set on the protocol Filters page of the
Advanced Page. If no IP addresses have been designated, then access
permission will be granted to all addresses.
For more information, refer to Advanced > Protocols: TCP/IP: IP Filters
on page 16.
Start > Status pages:
Network: POP3/SMTP
This allows you to verify the e-mail-related settings that have been made
on the POP3 and SMTP pages of the Advanced Page.
For more information, refer to Advanced > Management / E-mail: SMTP
on page 18 and Advanced > Management / E-mail: POP3: General on
page 20.
Start > Status pages:
Network: Logical Printers
This allows you to verify the settings that have been made on the Logical
Printers page of the Advanced Page.
For more information, refer to Advanced > Protocols: TCP/IP: Logical
Printers on page 16.
Start > Status pages:
Network: Netware
This allows you to verify the settings and status that have been made on
the Netware page of the Advanced Page.
For more information, refer to Advanced > Protocols: Netware: General
on page 17.
Start > Status pages:
Printer: General
This allows you to verify the settings that have been made on the Basic
page and the Printer page.
For more information, refer to Basic Page on page 10 and Printer Page
on page 13.
Start > Status pages:
Printer: I/F Independent
This allows you to verify the FRPO settings made under I/F Independent of
the Printer page.
For more information, refer to Printer > Defaults: FRPO Values:
Interface Independent/Interface Dependent on page 14.
Start > Status pages:
Printer: I/F Dependent
This allows you to verify the FRPO settings made under I/F Dependent of
the Printer page.
For more information, refer to Printer > Defaults: FRPO Values:
Interface Independent/Interface Dependent on page 14.
Page Description
Start > Information pages:
Contacts
This displays the dealer and service center contact information contained
in the Contact Information page of the Advanced page.
For more information, refer to Advanced > Information: Contacts on
page 22.
Start > Information pages:
About
The model number of this machine and Version of COMMAND CENTER
can be confirmed.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP1025 Operation Guide Command Center at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP1025 Operation Guide Command Center in the language / languages: English as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info