663191
3
Zoom out
Zoom in
Previous page
1/15
Next page
EN
Installation and repairs must be
made by a qualified bicycle
mechanic.
This manual assumes a level of
knowledge and skill consistent
with that of an experienced
bicycle assembler or bicycle
mechanic.
1
135mm
2. ASSEMBLY OF COMPONENTS
Installing the Sprocket
Remove the anti-shift
retainer (1) by pulling firmly away
from the NuVinci CVP.
Install a standard 9-spline,
3/32 inch (2.3mm) sprocket (2),
followed by the supplied sprocket
spacer (3, if required), and secure
with the sprocket snap ring (4).
The sprocket spacer is intended
for sprockets that are 3/32
inch (2.3mm) thick at the inner
diameter. If the inner diameter
is 0.17- 0.18 inch (4.3-4.5mm)
thick, the spacer should not be
used.
The N360 is compatible with
16 to 22 tooth sprockets.
Install the sprocket for a
chainline closest to the CVP.
If hub interface is not installed
immediately following the
sprocket, replace the anti-shift
retainer (1).
The NuVinci N360 is incompat-
ible with 1/8 inch (3.18mm)
single-speed chains and sprock-
ets. Use 3/32 inch (2.3mm)
chains and sprockets only.
Use of incompatible chains can
result in interference with the
hub interface and damage to
N360 components and may
result in a dangerous condition
for the rider.
If the sprocket is asymmetric,
incorrect installation can result
in interference with the hub
interface and damage to N360
components and may result in
a dangerous condition for the
rider.
1
2
3
4
2. ASSEMBLY OF COMPONENTS
3
4
EN
2.1
2.1
2.2
2.3
2.2
2.3
1
Wheel Building
The anti-shift retainer (1)
provides 135mm spacing, and
should remain on the CVP during
lacing and wheelbuilding.
Maximum spoke diameter is
#13 / 2.34mm.
Minimum spoke diameter is
#14 / 2.00mm.
Suggested lacing is a 2-cross
pattern for 26-inch and 700c
wheels.
Use a 2-cross pattern only if
the rim allows the nipples to
be effectively in-line with the
spokes.
For 24-inch or smaller wheels a
1-cross pattern is suggested.
Radial lacing is not recommended.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NuVinci N360 -2010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NuVinci N360 -2010 in the language / languages: English as an attachment in your email.

The manual is 7,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NuVinci N360 -2010

NuVinci N360 -2010 User Manual - German - 15 pages

NuVinci N360 -2010 User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info