663190
4
Zoom out
Zoom in
Previous page
1/15
Next page
EN
Hub Interface Orientation
and Installation Angle
Use the uninstalled hub
interface (1) to determine the
desired orientation.
fTypical orientation is forward,
parallel to the chain stay or
seat stay cable routing.
fMove the hub interface along
the dropout to ensure clearance
at different axle positions.
With the hub interface
oriented correctly inside the right
dropout, the installation angle (2)
is the indicated angle of the drop-
out (20 degrees in this example).
fUse the markings on the hub
interface to determine your
approximate installation angle.
Installation Angle:__________
2. ASSEMBLY OF COMPONENTS
5
Prior to installation, set the hub
interface to the full overdrive (H)
position (4).
Suspend the hub interface
over the right hand axle, and
align the axle ats (5) with the
installation angle from Step 2.5.
fAlternatively, a no-turn
washer (6) can be installed
over the hub interface to align
the installation angle.
When the installation angle is
aligned, ensure the hub interface
is set to full overdrive (H) and seat
the hub interface fully onto the shift
driver and the spline nut until it is
ush with the spline nut, as shown.
Thread the RH Nut (7),
serrations facing outward, onto
the axle and tighten to 10-15 Nm
(7-11 ft-lbs).
Install the rear wheel per Section 3.
2. ASSEMBLY OF COMPONENTS
6
2.4
2.5
2.7
2.8
2.9
2.10
Installing the Hub Interface
Remove the anti-shift retainer, if
installed (reference Step 2.2).
Ensure that markings between
the splined nut (2) and the shift
driver (3) are aligned. If not,
refer to Step 5.6.
2.6
1
2
2.4
2.5
20º
2
3
2.6
4
2.7
6
5
20º
2.8
2.9
7
2.10
EN
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NuVinci N 360 - 2012 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NuVinci N 360 - 2012 in the language / languages: English as an attachment in your email.

The manual is 5,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NuVinci N 360 - 2012

NuVinci N 360 - 2012 User Manual - German - 15 pages

NuVinci N 360 - 2012 User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info