23426
9
Zoom out
Zoom in
Previous page
1/14
Next page
CM1000/CM1000R
- The Leader in DJ Technology
©2000 Industries - 9 - http://www.numark.com
CROSSFADER
16. Replaceable Crossfader - achieves clean segues
between the two input channels selected by the
Crossfader Assign.
In this example "Hard left" selects Channel 1 and
"Hard right" selects Channel 4. With the crossfader
centered, both assigned channels are live. Use the
crossfader for fast and seamless segues from one
selected channel to the other.
Note:
The crossfader is replaceable in case of
failure. Simply remove all knobs from the facepanel
and unscrew the 5 screws that hold it in place.
Then remove the 2 fader screws that hold the
crossfader to the subchassis, lift it out and
disconnect its cable. Re-attach the new crossfader
and replace the faceplate and knobs back onto the
unit - you’re back in business!
17. Crossfader Slope – determines how quickly the
audio from the opposing side of the crossfader
activates. A tight curve (hard right) turns on the
opposing audio signal with very little crossfader
movement. A loose curve (hard left) makes very
long and smooth segues in transition.
18. Crossfader Assign Knob - determines which input
channel will be heard when the crossfader is moved
towards the knob and which channel is fader start.
Note:
All channels not assigned will remain active.
19. Fader Start – activates the crossfader to send play
and cue commands to your auto-start Numark CD
player or other popular brand using pulse
technology. For fader start, attach your mixer to a
remote start CD player using industry standard
1/8”(3.5mm) cables. When you move the crossfader
toward the active channel, the attached CD player
will start. When it is moved away, that side will cue
(similar to pressing the cue button).
OUTPUTS
20. 4-Band EQ control – adjusts the master output
according the setting on the rear panel. When the
unit is set for +/- 6 or 12dB the unit will increase or
decrease the frequency area adjusted.
21. Master Fader – to control the overall output level.
22. Panning – adjusts the balance of right and left
audio.
23. Stereo/Mono toggle - adjusts the Master output for
stereo or mono operation.
24. Stereo Auto Peak Hold Level Indicator- quickly
and accurately tracks level of audio sent to it by the
meter assign. The red LEDs for +3dB, +5dB and
+8dB hold program peaks for a second or two. With
peak metering, it's OK to be "in the red" as long as
+5dB or +8dB aren't constantly lit. When using as a
master output meter, set the crossover, equalizer
and power amp inputs to avoid distortion at each
step in the audio chain. Proper attention to the peak
meter results in the punchiest possible sound
without audible distortion. When used to adjust
the PFL levels, accurately match channel levels
with the Pre-fader gain controls before mixing them
together. The idea is to properly match PFL inputs,
not the input with the stereo output meter!
25. Zone Faders - controls speaker volume for a remote
zone or booth monitors.
NOTE:
This can also be used to supply line level
audio to a lighting controller or to lights that are
sound activated.
26. Power Indication LED – indicates when power is
applied to the unit and the rear panel power switch
is on.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numark CM1000R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numark CM1000R in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info