817964
4
Zoom out
Zoom in
Previous page
1/14
Next page
connects or disconnects from the MQTT server.
When the debug mode of the Smart Lock and “LED signal on the Smart Lock” are
both active, the red LED of the Smart Lock acts as a traffic indicator for incoming
WIFI packets, similar to a traffic indicator of a network switch. Turn off “LED signal on
the Smart Lock” to disable this diagnostic feature.
Home Assistant Discovery and Allow Locking” are per default activated and can not
be deactivated.
2.2 Provisioning
Provisioning of an MQTT server is done via the Nuki App in the Device Administration >
MQTT section.
It allows users to enable/disable the API, enter the credentials (username & password) and a
hostname or IPv4 address for the MQTT server.
In addition Home Assistant Discovery (Default: on) and Allow Locking” (Default: on) can be
activated and deactivated.
2.3 Connection
Once the API has been activated and provisioned the Nuki device tries to establish a
connection to the entered MQTT server on port 1883.
Connections will only be established to MQTT servers in the local LAN. I.e. either the
hostname has to resolve to a local IP or a local IP is given as hostname (10.0.0.0 -
10.255.255.255, 172.16.0.0 - 172.31.255.255, 192.168.0.0 - 192.168.255.255).
The current status of the connection is visible inside the Nuki Apps Device Administration
MQTT section.
The reconnect mechanism for the Smart Lock 3.0 WiFi connection is bound to a successful
connection to the Nuki server. i.e. you can not isolate the Smart Lock from the internet as
this will lead to reconnect attempts involving WiFi log off/ons with exponentially growing
downtimes in between, which will also lead to disconnects of the MQTT connection.
Likewise an unstable internet connection can lead to MQTT reconnects and downtimes.
2.4 Security
The MQTT API inside Smart Lock 3.0 Pro does not support encrypted connections because of
memory constraints. Only connections to unencrypted MQTT servers are possible.
Nuki Home Solutions GmbH
Münzgrabenstraße 92/4 • 8010 Graz • Austria • F +43 316 22 84 12 50
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nuki MQTT API at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nuki MQTT API in the language / languages: English as an attachment in your email.

The manual is 0.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info