520224
4
Zoom out
Zoom in
Previous page
1/11
Next page
5
The NRX EVO 500EH replicates the operation of the
handset lifter allowing control of a phone call by the 'Talk
Button' located on the headset. Once the line has been
seized by the headset, the 'Speaker/Headset' button on the
telephone is disabled until the call is completed by
pressing the 'Talk Button' on the headset again.
1.3 Telephone Set-Up
In standby mode, press the MENU button twice, the
display will show SYSTEM.
Turning the jog wheel will switch among the various
setting modes of the Main System Menu loop as shown
below:
Set Time
Scroll to 'SET TIME' on the System Menu and then press
the Jog Wheel. Turn the Jog Wheel to the desired time
and date pressing the wheel for confirmation after setting
HOUR, MINUTE, DATE & MONTH.
Set Recall
Scroll to 'SET RECALL' on the System Menu and then
Installation & Telephone Set-Up
4
Telephone Set-Up
press the Jog Wheel. Scroll to TBR (Timed Break
Recall) or EARTH (Earth Recall) then press the Jog
Wheel to confirm.
If TBR is selected, after pressing the Jog Wheel you will
need to select the TBR timing (100ms to 1200ms).
Once again press the Jog Wheel to confirm your
selection. The standard setting for the UK is normally
100ms.
NOTE: By default your NRX EVO 500EH is factory
set at TBR 100ms.
LCD Contrast
Scroll to 'LCD CONTRAST' on the System Menu and
then press the Jog Wheel. Select the desired LCD
contrast then press the Jog Wheel again. The default
setting is 3.
Message Waiting Type
Scroll to 'MESSAGE WAITING' on the System Menu
options and then press the Jog Wheel. Scroll to one of
the Following options then press the Jog Wheel:
? LINE REVERSAL
? 90V DC
? HIPATH
? AT&T/ALCATEL
? ERICSSON MD-110
? FSK MWI
If Line Reversal is selected - Select Polarity Normal,
Polarity Reversal or OFF and then press the Jog Wheel
again. This should be set to OFF if Line Reversal is not
required.
For the other message waiting options - Select ON or
OFF and then press the Jog Wheel. They should be set to
OFF if not required. If Siemens Hipath or Ericsson MD-
110 is selected the Ringer Sensitivity switch (SW1) on
the base of the telephone should be set ‘Low’. At all
other times this should be switch to ‘High’.
Dial Mode
Scroll to 'DIAL MODE' on the System Menu and then
press the Jog Wheel. Select either Tone or Pulse
dialling then press the Jog Wheel again.
The default setting for the telephone is Tone dialling.
DIAL MODE
SET RECALL
LCD CONTRAST
SECURITY
MODE
SET TIME
MESSAGE
WAITING
AREA CODE
TIME MODE
PABX PREFIX
AUTOREDIAL
MODE
CLIP MODE
NEW ZEALAND
CLID
HS Auto Answer
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NRX EVO 500EH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NRX EVO 500EH in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info